200-125 Assessment: Examcollection examination braindumps
Exam Number/Code : 200-125
Exam Name : CCNA Cisco Certified Network Associate CCNA (v3.0)
Vendor: Cisco
Associated Accreditation:Cisco
Questions plus Solutions : [productnum]
Latest Up-date Occasion: [productupdatetime]
Price: [productprice]
2021 Oct 200-125 free practice questions
Q101. - (Topic 9)
Which two commands can you enter to verify that a configured NetFlow data export is operational? (Choose two.)
A. show ip flow export
B. show ip cache flow
C. ip flow ingress
D. ip flow egress
E. interface ethernet 0/0
F. ip flow-export destination
Answer: A,B
Q102. - (Topic 7)
What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter
Answer: A
Q103. - (Topic 9)
What are two requirements for an HSRP group? (Choose two.)
A. exactly one active router
B. one or more standby routers
C. one or more backup virtual routers
D. exactly one standby active router
E. exactly one backup virtual router
Answer: A,B
Q104. - (Topic 2)
Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?
A. 802.3ad
B. 802.1w
C. 802.1D
D. 802.1Q
Answer: D
Q105. - (Topic 6)
Refer to the exhibit.
An attempt to deny web access to a subnet blocks all traffic from the subnet. Which interface command immediately removes the effect of ACL 102?
A. no ip access-class 102 in
B. no ip access-class 102 out
C. no ip access-group 102 in
D. no ip access-group 102 out
E. no ip access-list 102 in
Answer: D
Renovate 200-125 question:
Q106. - (Topic 5)
In GLBP, which router will respond to client ARP requests?
A. The active virtual gateway will reply with one of four possible virtual MAC addresses.
B. All GLBP member routers will reply in round-robin fashion.
C. The active virtual gateway will reply with its own hardware MAC address.
D. The GLBP member routers will reply with one of four possible burned in hardware addresses.
Answer: A
Q107. CORRECT TEXT - (Topic 7)
Answer: Corp1#conf t
Corp1(config)# access-list 128 permit tcp host 192.168.240.1 host 172.22.141.26 eq www
Corp1(config)# access-list 128 deny tcp any host 172.22.141.26 eq www
Corp1(config)# access-list 128 permit ip any any
Corp1(config)#int fa0/1
Corp1(config-if)#ip access-group 128 out
Corp1(config-if)#end
Corp1#copy run startup-config
Q108. - (Topic 9)
Which spanning-tree protocol rides on top of another spanning-tree protocol?
A. MSTP
B. RSTP
C. PVST+
D. Mono Spanning Tree
Answer: A
Q109. - (Topic 5)
In a GLBP network, who is responsible for the ARP request?
A. AVF
B. AVG
C. Active Router
D. Standby Router
Answer: B
Q110. - (Topic 4)
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
see more 200-125 dumps