♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 100-105 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 100-105 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/100-105-exam-dumps.html
Q41. - (Topic 3)
Refer to the exhibit.
The two routers have had their startup configurations cleared and have been restarted. At a minimum, what must the administrator do to enable CDP to exchange information between R1 and R2?
A. Configure the router with the cdp enable command.
B. Enter no shutdown commands on the R1 and R2 fa0/1 interfaces.
C. Configure IP addressing and no shutdown commands on both the R1 and R2 fa0/1 interfaces.
D. Configure IP addressing and no shutdown commands on either of the R1 or R2 fa0/1 interfaces.
Answer: B
Explanation:
If the no shut down commands are not entered, then CDP can exchange information between the two routers. By default, all Cisco device interfaces and ports are shut down and need to be manually enabled.
Q42. - (Topic 3)
Refer to the exhibit.
The enterprise has decided to use the network address 172.16.0.0. The network administrator needs to design a classful addressing scheme to accommodate the three subnets, with 30, 40, and 50 hosts, as shown. What subnet mask would accommodate this network?
A. 255.255.255.192
B. 255.255.255.224
C. 255.255.255.240
D. 255.255.255.248
E. 255.255.255.252
Answer: A
Explanation:
Subnet mask A i.e. 255.255.255.192 with CIDR of /26 which means 64 hosts per subnet which are sufficient to accommodate even the largest subnet of 50 hosts.
Q43. - (Topic 3)
Refer to the exhibit.
What is the simplest way to configure routing between the regional office network 10.89.0.0/20 and the corporate network?
A. router1(config)#ip route 10.89.0.0 255.255.240.0 10.89.16.2
B. router2(config)#ip route 10.89.3.0 255.255.0.0 10.89.16.2
C. router1(config)#ip route 10.89.0.0 255.255.240.0 10.89.16.1
D. router2(config)#ip route 0.0.0.0 0.0.0.0 10.89.16.1
Answer: D
Explanation:
The next hop of the static route should be 10.89.16.1, which is the IP address for router R1 in this example. Since this router is a stub router with only a single connection to the WAN, the simplest thing to do is to configure a single static default route back to the HQ network.
Q44. - (Topic 3)
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)
A. Router(config)# router ospf 0
B. Router(config)# router ospf 1
C. Router(config)# router ospf area 0
D. Router(config-router)# network 192.168.16.0 0.0.0.255 0
E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0
Answer: B,E
Explanation:
In the router ospf command, the ranges from 1 to 65535 so o is an invalid number -> but To configure OSPF, we need a wildcard in the “network” statement, not a subnet mask. We also need to assgin an area to this process.
Q45. - (Topic 7)
What is the default lease time for a DHCP binding?
A. 24 hours
B. 12 hours
C. 48 hours
D. 36 hours
Answer: A
Explanation: By default, each IP address assigned by a DHCP Server comes with a one-day lease, which is the amount of time that the address is valid. To change the lease value for an IP address, use the following command in DHCP pool configuration mode:
Q46. - (Topic 3)
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; a password mismatch.
C. There is an OSPF hello and dead interval mismatch.
D. There is a missing network command in the OSPF process on R5.
Answer: C
Explanation:
The “show ip ospf interface command on R3 and R5 shows that the hello and dead intervals do not match. They are 50 and 200 on R3 and 10 and 40 on R5.
Topic 4, Infrastructure Services
Q47. - (Topic 7)
Which function enables an administrator to route multiple VLANs on a router?
A. IEEE 802 1X
B. HSRP
C. port channel
D. router on a stick
Answer: D
Q48. - (Topic 5)
The hosts in the LAN are not able to connect to the Internet. Which commands will correct this issue?
A. Option A
B. Option B
C. Option C
D. Option D
E. Option E
Answer: B
Explanation:
Do a “show ip int brief” and you will see that Fa0/1 has an IP address assigned, but it is shut down.
Q49. - (Topic 5)
How can you ensure that only the MAC address of a server is allowed by switch port Fa0/1?
A. Configure port Fa0/1 to accept connections only from the static IP address of the server.
B. Configure the server MAC address as a static entry of port security.
C. Use a proprietary connector type on Fa0/1 that is incomputable with other host connectors.
D. Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.
Answer: B
Explanation:
When the MAC address is configured as static entry, no other address is allowed.
Q50. - (Topic 4)
When configuring NAT, the Internet interface is considered to be what?
A. local
B. inside
C. global
D. outside
Answer: D
Explanation:
The first step to deploy NAT is to define NAT inside and outside interfaces. You may find it easiest to define your internal network as inside, and the external network as outside. However, the terms internal and external are subject to arbitration as well. This figure shows an example of this.
2a.gif
Reference: http://www.cisco.com/c/en/us/support/docs/ip/network-address-translation-nat/13772-12.html#topic2
