Actualtests icnd2 200 105 Questions are updated and all 105 200 answers are verified by experts. Once you have completely prepared with our ccna 200 105 exam prep kits you will be ready for the real cisco 200 105 exam without a problem. We have Avant-garde Cisco 105 200 dumps study guide. PASSED ccna routing and switching icnd2 200 105 official cert guide First attempt! Here What I Did.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 200-105 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-105 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/200-105-exam-dumps.html
Q51. - (Topic 3)
Which two statistics appear in show frame-relay map output? (Choose two.)
A. the number of BECN packets that are received by the router
B. the value of the local DLCI
C. the number of FECN packets that are received by the router
D. the status of the PVC that is configured on the router
E. the IP address of the local router
Answer: B,D
Explanation:
Frame Relay Commands (map-class frame-relay through threshold ecn)
http://www.cisco.com/en/US/docs/ios/12_2/wan/command/reference/wrffr4.html#wp102934
Examples
The following is sample output from the show frame-relay map command:
Router#show frame-relay map Serial 1 (administratively down): ip 10.108.177.177
dlci 177 (0xB1,0x2C10), static, broadcast,
CISCO
TCP/IP Header Compression (inherited), passive (inherited)
Q52. - (Topic 3)
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following are required to solve this? (Choose three)
A. configure static frame relay map entries for each subinterface network.
B. remove the ip address from the physical interface
C. create the virtual interfaces with the interface command
D. configure each subinterface with its own IP address
E. disable split horizon to prevent routing loops between the subinterface networks
F. encapsulate the physical interface with multipoint PPP
Answer: B,C,D
Explanation:
How To Configure Frame Relay Subinterfaces http://www.orbit-computer-solutions.com/How-To-Configure-Frame-Relay-Subinterfaces.php
Step to configure Frame Relay subinterfaces on a physical interface:
1. Remove any network layer address (IP) assigned to the physical interface. If the physical interface has an address, frames are not received by the local subinterfaces.
2. Configure Frame Relay encapsulation on the physical interface using the encapsulation frame-relay command.
3. For each of the defined PVCs, create a logical subinterface. Specify the port number, followed by a period (.) and the subinterface number. To make troubleshooting easier, it is suggested that the subinterface number matches the DLCI number.
4. Configure an IP address for the interface and set the bandwidth.
5. Configure the local DLCI on the subinterface using the frame-relay interface-dlci command. Configuration Example: R1>enable R1#configure terminal R1(config)#interface serial 0/0/0 R1(config-if)#no ip address R1(config-if)#encapsulation frame-relay R1(config-if)#no shutdown R1(config-if)#exit R1(config-subif)#interface serial 0/0/0.102 point-to-point R1(config-subif)#ip address 192.168.1.245 255.255.255.252 R1(config-subif)#frame-relay interface-dlci 102 R1(config-subif)#end R1#copy running-config startup-config
Q53. - (Topic 2)
Refer to the exhibit.
Host A pings interface S0/0 on router 3, what is the TTL value for that ping?
A. 253
B. 252
C. 255
D. 254
Answer: A
Explanation:
From the CCNA ICND2 Exam book: “Routers decrement the TTL by 1 every time they forward a packet; if a router decrements the TTL to 0, it throws away the packet. This prevents packets from rotating forever.” I want to make it clear that before the router forwards a packet, the TTL is still remain the same. For example in the topology above, pings to S0/1 and S0/0 of Router 2 have the same TTL.
The picture below shows TTL values for each interface of each router and for Host B.
Notice that Host A initializes ICMP packet with a TTL of 255:
Q54. - (Topic 2)
Refer to the exhibit.
Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
Answer: B,C
Explanation: A loopback interface never comes down even if the link is broken so it provides stability for the OSPF process (for example we use that loopback interface as the router-id) - B is correct.
The router-ID is chosen in the order below:
The highest IP address assigned to a loopback (logical) interface. If a loopback interface is not defined, the highest IP address of all active router’s physical interfaces will be chosen.
-The loopback interface will be chosen as the router ID of RouterB - C is correct.
Q55. - (Topic 2)
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
A. Bandwidth
B. Bandwidth and Delay
C. Bandwidth, Delay, and MTU
D. Bandwidth, MTU, Reliability, Delay, and Load
Answer: A
Explanation:
http://www.cisco.com/en/US/tech/tk365/technologies_white_paper09186a0080094e9e.sht ml#t6
OSPF Cost
The cost (also called metric) of an interface in OSPF is an indication of the overhead required to send packets across a certain interface. The cost of an interface is inversely proportional to the bandwidth of that interface. A higher bandwidth indicates a lower cost. There is more overhead (higher cost) and time delays involved in crossing a 56k serial line than crossing a 10M Ethernet line. The formula used to calculate the cost is: Cost= 10000 0000/bandwidth in bps
For example, it will cost 10 EXP8/10 EXP7 = 10 to cross a 10M Ethernet line and will cost 10 EXP8/1544000 =64 to cross a T1 line. By default, the cost of an interface is calculated based on the bandwidth; you can force the cost of an interface with the ip ospf cost <value> interface sub configuration mode command.
Q56. - (Topic 3)
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut
B. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp Main(config-if)# no shut
C. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation frame-relay Main(config-if)# authentication chap Main(config-if)# no shut
D. Main(config)# interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)# no shut
Answer: B
Explanation:
Cisco High-Level Data Link Controller (HDLC) is the Cisco proprietary protocol for sending data over synchronous serial links using HDLC. So HDLC runs only in Cisco router. PPP is not proprietary protocol it's a open source every cisco router and non-cisco router understand the PPP protocol.So we need to configure the PPP protocol if connection is between cisco and non-cisco router.
Q57. - (Topic 1)
Refer to the exhibit.
At the end of an RSTP election process, which access layer switch port will assume the discarding role?
A. Switch3, port fa0/1
B. Switch3, port fa0/12
C. Switch4, port fa0/11
D. Switch4, port fa0/2
E. Switch3, port Gi0/1
F. Switch3, port Gi0/2
Answer: C
Explanation:
In this question, we only care about the Access Layer switches (Switch3 & 4). Switch 3 has a lower bridge ID than Switch 4 (because the MAC of Switch3 is smaller than that of Switch4) so both ports of Switch3 will be in forwarding state. The alternative port will surely belong to Switch4. Switch4 will need to block one of its ports to avoid a bridging loop between the two switches. But how does Switch4 select its blocked port? Well, the answer is based on the BPDUs it receives from Switch3. A BPDU is superior than another if it has:
1. A lower Root Bridge ID2. A lower path cost to the Root3. A lower Sending Bridge ID4. A lower Sending Port ID
These four parameters are examined in order. In this specific case, all the BPDUs sent by Switch3 have the same Root Bridge ID, the same path cost to the Root and the same Sending Bridge ID. The only parameter left to select the best one is the Sending Port ID (Port ID = port priority + port index). In this case the port priorities are equal because they use the default value, so Switch4 will compare port index values, which are unique to each port on the switch, and because Fa0/12 is inferior to Fa0/1, Switch4 will select the port connected with Fa0/1 (of Switch3) as its root port and block the other port -> Port fa0/11 of Switch4 will be blocked (discarding role)
Q58. - (Topic 3)
Which PPP subprotocol negotiates authentication options?
A. NCP
B. ISDN
C. SLIP
D. LCP
E. DLCI
Answer: D
Explanation:
A protocol that establishes, configures, and tests data link connections used by the PPP Link Control Protocol offers PPP encapsulation different options, including the following: Authentication - options includes PAP and CHAP Compression - Data compression increases the throughput on a network link, by reducing the amount of data that must be transmitted. Error Detection -Quality and Magic numbers are used by PPP to ensure a reliable, loop-free data link. Multilink - Supported in IOS 11.1 and later, multilink is supported on PPP links between Cisco routers. This splits the load for PPP over two or more parallel circuits and is called a bundle.
Q59. - (Topic 2)
Refer to the exhibit.
Given the output from the “show ip eigrp topology” command, which router is the feasible successor?
A)
B)
C)
D)
A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
Answer: B
Explanation:
To be the feasible successor, the Advertised Distance (AD) of that route must be less than the Feasible Distance (FD) of the successor. From the output of the “show ip eigrp topology
10.0.0.5 255.255.255.255 we learn that the FD of the successor is 41152000. Now we will mention about the answers, in the “Composite metric is (…/…)” statement the first parameter is the FD while the second parameter is the AD of that route. So we need to find out which route has the second parameter (AD) less than 41152000 -> only answer B satisfies this requirement with an AD of 128256.
Reference: http://networklessons.com/eigrp/eigrp-neighbor-and-topology-table-explained/
Q60. - (Topic 2)
What are two benefits of using a single OSPF area network design? (Choose two.)
A. It is less CPU intensive for routers in the single area.
B. It reduces the types of LSAs that are generated.
C. It removes the need for virtual links.
D. It increases LSA response times.
E. It reduces the number of required OSPF neighbor adjacencies.
Answer: B,C
Explanation:
OSPF uses a LSDB (link state database) and fills this with LSAs (link state advertisement). The link types are as follows:
LSA Type 1:. Router LSA
LSA Type 2:.. . . . . . . . Network LSA
LSA Type 3:. Summary LSA
LSA Type 4:. Summary ASBR LSA
LSA Type 5:. Autonomous system external LSA
LSA Type 6:. Multicast OSPF LSA
LSA Type 7:. Not-so-stubby area LSA
LSA Type 8:. External attribute LSA for BGP
If all routers are in the same area, then many of these LSA types (Summary ASBR LSA, external LSA, etc) will not be used and will not be generated by any router.
All areas in an Open Shortest Path First (OSPF) autonomous system must be physically connected to the backbone area (Area 0). In some cases, where this is not possible, you can use a virtual link to connect to the backbone through a non-backbone area. You can also use virtual links to connect two parts of a partitioned backbone through a non-backbone area. The area through which you configure the virtual link, known as a transit area, must have full routing information. The transit area cannot be a stub area. Virtual links are not ideal and should really only be used for temporary network solutions or migrations. However, if all locations are in a single OSPF area this is not needed.
