we provide Download Cisco 125 200 rapidshare which are the best for clearing 200 125 ccna book test, and to get certified by Cisco CCNA Cisco Certified Network Associate CCNA (v3.0). The 200 125 ccna v3 0 Questions & Answers covers all the knowledge points of the real cisco 200 125 exam. Crack your Cisco ccna 200 125 dumps Exam with latest dumps, guaranteed!
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/200-125-exam-dumps.html
Q151. - (Topic 4)
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following procedures are required to accomplish this task? (Choose three.)
A. Remove the IP address from the physical interface.
B. Encapsulate the physical interface with multipoint PPP.
C. Create the virtual interfaces with the interface command.
D. Configure each subinterface with its own IP address.
E. Disable split horizon to prevent routing loops between the subinterface networks.
F. Configure static Frame Relay map entries for each subinterface network.
Answer: A,C,D
Explanation:
For multiple PVC’s on a single interface, you must use subinterfaces, with each subinterface configured for each PVC. Each subinterface will then have its own IP address, and no IP address will be assigned to the main interface.
Q152. - (Topic 8)
What is one requirement for interfaces to run IPv6?
A. An IPv6 address must be configured on the interface.
B. An IPv4 address must be configured.
C. Stateless autoconfiguration must be enabled after enabling IPv6 on the interface.
D. IPv6 must be enabled with the ipv6 enable command in global configuration mode.
Answer: A
Explanation: To use IPv6 on your router, you must, at a minimum, enable the protocol and assign IPv6 addresses to your interfaces.
Q153. - (Topic 8)
Why has the Branch3 router lost connectivity with R1?
Use only show commands to troubleshoot because usage of the debug command is restricted on the Branch3 and R1 routers.
A. A PPP chap hostname mismatch is noticed between Branch3 and R1.
B. A PPP chap password mismatch is noticed between Branch3 and R1.
C. PPP encapsulation is not configured on Branch3.
D. The PPP chap hostname and PPP chap password commands are missing on the Branch3 router.
Answer: A
Q154. - (Topic 8)
Which two security appliances will you use in a network? (Choose two.)
A. ATM
B. IDS
C. IOS
D. IOX
E. IPS
F. SDM
Answer: B,E
Q155. - (Topic 7)
Which protocol can cause overload on a CPU of a managed device?
A. Netflow
B. WCCP
C. IP SLA
D. SNMP
Answer: D
Explanation:
Sometimes, messages like this might appear in the router console:
%SNMP-3-CPUHOG: Processing [chars] of [chars]
They mean that the SNMP agent on the device has taken too much time to process a request.
You can determine the cause of high CPU use in a router by using the output of the show process cpu command.
Note: A managed device is a part of the network that requires some form of monitoring and
management (routers, switches, servers, workstations, printers…).
Q156. DRAG DROP - (Topic 7)
Drag each category on the left to its corresponding router output line on the right. Each router output line is the result of a show ip interface command. Not all categories are used.
Answer:
Explanation:
A simple way to find out which layer is having problem is to remember this rule: “the first statement is for Layer 1, the last statement is for Layer 2 and if Layer 1 is down then surely Layer 2 will be down too”, so you have to check Layer 1 before checking Layer 2. For example, from the output “Serial0/1 is up, line protocol is down” we know that it is a layer 2 problem because the first statement (Serial0/1 is up) is good while the last statement (line protocol is down) is bad. For the statement “Serial0/1 is down, line protocol is down”, both layers are down so the problem belongs to Layer 1.
There is only one special case with the statement “…. is administrator down, line protocol is down”. In this case, we know that the port is currently disabled and shut down by the administrators.
Q157. - (Topic 5)
In GLBP, which router will respond to client ARP requests?
A. The active virtual gateway will reply with one of four possible virtual MAC addresses.
B. All GLBP member routers will reply in round-robin fashion.
C. The active virtual gateway will reply with its own hardware MAC address.
D. The GLBP member routers will reply with one of four possible burned in hardware addresses.
Answer: A
Explanation:
One disadvantage of HSRP and VRRP is that only one router is in use, other routers must wait for the primary to fail because they can be used. However, Gateway Load Balancing Protocol (GLBP) can use of up to four routers simultaneously. In GLBP, there is still only one virtual IP address but each router has a different virtual MAC address. First a GLBP group must elect an Active Virtual Gateway (AVG). The AVG is responsible for replying ARP requests from hosts/clients. It replies with different virtual MAC addresses that correspond to different routers (known as Active Virtual Forwarders – AVFs) so that clients can send traffic to different routers in that GLBP group (load sharing).
Q158. - (Topic 7)
Scenario:
Refer to the topology. Your company has decided to connect the main office with three
other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R4 in the Branch1 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a Layer 2 issue; an encapsulation mismatch on serial links.
C. There is an OSPF hello and dead interval mismatch.
D. The R3 router ID is configured on R4.
Answer: A
Explanation:
A show running-config command on R3 and R4 shows that R4 is incorrectly configured for area 2:
Q159. CORRECT TEXT - (Topic 7)
A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed.
The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted.
Access to the router CLI can be gained by clicking on the appropriate host.
All passwords have been temporarily set to "cisco".
The Core connection uses an IP address of 198.18.247.65
The computers in the Hosts LAN have been assigned addresses of 192.168.240.1 - 192.168.240.254
✑ host A 192.168.240.1
✑ host B 192.168.240.2
✑ host C 192.168.240.3
Answer:
Corp1#conf t
Corp1(config)# access-list 128 permit tcp host 192.168.240.1 host 172.22.141.26 eq www Corp1(config)# access-list 128 deny tcp any host 172.22.141.26 eq www
Corp1(config)# access-list 128 permit ip any any Corp1(config)#int fa0/1
Corp1(config-if)#ip access-group 128 out Corp1(config-if)#end
Corp1#copy run startup-config
Q160. - (Topic 8)
Which technology allows a large number of private IP addresses to be represented by a smaller number of public IP addresses?
A. NAT
B. NTP
C. RFC 1631
D. RFC 1918
Answer: A
