Master the ccna wireless 200 355 Implementing Cisco Wireless Network Fundamentals content and be ready for exam day success quickly with this Actualtests ccna wireless 200 355 official cert guide pdf practice test. We guarantee it!We make it a reality and give you real ccna wireless 200 355 official cert guide pdf free download questions in our Cisco ccna wireless 200 355 official cert guide pdf braindumps.Latest 100% VALID Cisco 200 355 wifund Exam Questions Dumps at below page. You can use our Cisco ccna wireless 200 355 dumps braindumps and pass your exam.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 200-355 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-355 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/200-355-exam-dumps.html
Q191. Which CAPWAP AP management-access method is available as the default setting?
A. only the console port
B. the console port and SSH
C. the console port, SSH, and HTTPS
D. SSH only
Answer: A
Q192. Which two statements about WiMAX technology are true? (Choose two.)
A. WiMAX is defined by 802.11i.
B. Typically, fixed WiMAX networks have a higher-gain directional antenna installed near the client.
C. WiMAX is capable of working as a long-range system over several miles.
D. WiMAX works only for licensed frequencies.
Answer: B,C
Q193. Which of the following are three functions of Cisco RRM? (Choose three.)
A. TPC
B. intercontroller roaming
C. dynamic channel assignment
D. intracontroller roaming
E. coverage hole detection
Answer: A,C,E
Q194. During Layer 2 intercontroller roaming, which two items change? (Choose two.)
A. SSID
B. VLAN
C. IP address
D. AP
E. controller
Answer: D,E
Q195. The administrator needs to create a report that shows all controllers, APs, and Cisco 3300 Series MSEs in the WLAN, including hardware and software information. Which report includes this information?
A. Device > Inventory
B. Mesh > Nodes
C. Network Summary > Executive Summary
D. Network Summary > 802.11 Summary
Answer: A
Q196. Which option best describes the limitation of a client that is attempting to manage a WLC while using the client wireless adapter connection to the wireless infrastructure?
A. Controllers must be managed using only secure protocols (that is, SSH and HTTPS), not nonsecure protocols (that is, HTTP and Telnet).
B. Read-write access is not available; only read-only access is supported.
C. Uploads and downloads from the controller are not allowed.
D. Wireless clients can manage other controllers, but not the same controller and the AP to which the client is associated.
Answer: C
Q197. When using multiple SSIDs on a lightweight AP, how does the traffic of each SSID reach the 802.3 network?
A. provide routing between them at the core so that the SSIDs can reach the internet
B. configure 802.11q trunking on the Ethernet switch port that is connected to the AP
C. configure ACLs at the switch port that will allow all desired SSIDs to pass traffic
D. configure the SSIDs on the WLC and it will regulate the traffic based on traffic type
Answer: B
Q198. Refer to the exhibit.
Which three switch port types are valid for these connections? (Choose three.)
A. access
B. port-channel
C. port-channel trunk
D. trunk
E. port-channel access
F. routed port
Answer: A,C,D
Q199. Refer to the exhibit. A customer is using central web authentication with a Cisco 5508 Wireless Controller and Cisco Identity Services Engine. An error occurs when wireless clients are redirected to the hosted splash page. What is causing the client error?
A. Secure Web Mode is disabled on the WLC.
B. OCSP is disabled on the WLC.
C. Management Via Dynamic Interface is disabled on the WLC.
D. Ethernet Multicast Forwarding is enabled on the WLC.
Answer: A
Q200. Refer to the exhibit. The wireless engineer has deployed the Cisco 5508 Wireless Controller. The controller is responding on the service port; however, it will not respond on the management interface. Which configuration revision will fix the management interface?
A. On the switch interface, configure switch(config-if)#switchport trunk allowed vlan add 10.
B. On the WLC management interface, disable LAG on the management network.
C. On the switch interface, configure switch(config-if)#switchport trunk allowed vlan 10.
D. On the WLC management interface, change the VLAN ID to 20.
E. On the switch interface, configure no spanning-tree portfast trunk.
F. On WLC Controller > General, disable LAG and reboot.
Answer: A
