Cisco 300-360 Train Inquiries & Advice in addition to Cisco 300-360 Train review substances with Ucertify is usually modified consistently as well while using latest Cisco 300-360 Audit Goals and gives anyone 100% good results inside 300-360 audit . The idea doesn?¡¥t cost you too much to get Ucertify Cisco 300-360 whilst letting you move a persons Cisco 300-360 Qualification Audit against your 1st look at. All of our Cisco 300-360 in addition to 300-360 protect 100% 300-360 Audit Goals.
2021 Mar 300-360 free question
Q11. A customer has dual-band devices that they want to use 40 MHz channels. If the customer is using Cisco 3600 Series access points with a 5508 controller. Which setting assists with this change?
A. Enable band select globally.
B. Enable aggressive load balancing.
C. Disable lower data rates on 802 .11G GHz radios.
D. Disable overlapping 802.11G channels.
Answer: A
Q12. The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: B
Q13. A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?
A. Deploy the specified access points per area type.
B. Resurvey and adjust the design.
C. Increase the Tx power on incorrectly surveyed access points.
D. Deploy unsurveyed access points to the design.
Answer: B
Q14. An engineer is assigned to provide wireless coverage in a provincial capital building. Due to the age and historic nature of the building, the ability to run new copper Ethernet cable to desired AP locations is limited. Which requirement should the engineer specify to overcome this restriction?
A. Deploy access points where the survey indicates and connect them via fiber optic cable, using a mediaadapter, and locally provide power.
B. Deploy access points to each phone location converting two spare pairs of copper from the phone line toEthernet and locally provide power.
C. Deploy access point devices where limited cable can be run or exists and connect high- gain antennas andincrease Tx power to increase cell size.
D. Deploy RAP where limited cable can be run or exists, and extend coverage using MAP.
Answer: D
Q15. Which two best practices should be considered when a customer wants to purchase and implement Voice over Wireless for Cisco 7925 IP Phones? (Choose two.)
A. Enable lower data rates for 2.4-GHz data WLAN and higher data rates for phones.
B. Use a separate Cisco Wireless Lan Controller.
C. Enable 802.1x and Cisco Centralized Key Management for phone authentication.
D. Use dedicated Access Points only for Voice over Wireless.
E. Set data for 2.4 GHz and voice for 5 GHz using separate SSIDs.
Answer: C,E
Rebirth 300-360 practice:
Q16. An engineer plugs in a Cisco Aironet 2700 Series Access Point and it is running in low power. Which three power requirements should be verified? (Choose three.)
A. 802.3ac compliant
B. 802.3at compliant
C. AP requires 43 VDC to function in full power.
D. AIR-PWRINJ3 power injector should be used.
E. AP requires 57 VDC to function in full power.
F. AIR-PWRINJ4 power injector should be used.
Answer: B,E,F
Explanation:
The access point should be powered by any 802.3at compliant device.
The recommended external power supply for the access point is the Cisco AIR-PWR-B power supply. The access point can also be powered by the following optional external power sources:
– Access point power injector (AIR-PWRINJ4)
– Any 802.3af compliant power injector is supported, but in this case the access point will dynamically shift from 3x4 to 3x3.
Reference: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/2700/quick/guide/ap2700getst art.html
Q17. When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to support location services versus data and voice services?
A. Data services have the lowest density of APs compared to location services, which has the highest density.
B. Data services have a lower density of APs compared to location services, but more than voice.
C. Voice services have the highest density of APs over location and data services.
D. Voice and data services require a higher density of APs than location services.
Answer: A
Q18. A customer has deployed an N+N redundant wireless infrastructure. In this deployment, the access points have been salt and peppered between controllers. What configuration would be necessary to cut down on the use of mobility tunnels for voice clients?
A. mobility anchor
B. KIS based CAC
C. media session snooping
D. re-anchor roamed voice clients
Answer: D
Q19. A customer has a business-critical voice network and wants to be alerted whenever voice clients move out of a coverage area and experience RSSI below -67 dBm on the 5 GHz band. Which option can be configured on the wireless controller to alert network administrators when this limit is surpassed?
A. EDCA; voice optimized
B. SIP voice sample interval
C. 802.11a voice RSSI coverage threshold
D. traffic stream metrics
Answer: C
Q20. When reviewing a design for a voice over wireless deployment, what per-call bandwidth cost should be factored in when determining maximum calls per cell using SIP and G.711u as the codec?
A. 64 bytes
B. 8 bytes
C. 80 bytes
D. 10 bytes
Answer: C
see more 300-360 dumps
