ccent 100-101 study guide [May 2016]

High quality of 100-101 free practice questions materials and bible for Cisco certification for IT examinee, Real Success Guaranteed with Updated 100-101 pdf dumps vce Materials. 100% PASS CCNA Interconnecting Cisco Networking Devices 1 (ICND1) exam Today!

2016 May 100-101 Study Guide Questions:

Q21. Refer to the exhibit. 


The junior network support staff provided the diagram as a recommended configuration for the first phase of a four-phase network expansion project. The entire network expansion will have over 1000 users on 14 network segments and has been allocated this IP address space. 

192.168.1.1 through 192.168.5.255 

192.168.100.1 through 192.168.100.255 

What are three problems with this design? (Choose three.) 

A. The AREA 1 IP address space is inadequate for the number of users. 

B. The AREA 3 IP address space is inadequate for the number of users. 

C. AREA 2 could use a mask of /25 to conserve IP address space. 

D. The network address space that is provided requires a single network-wide mask. 

E. The router-to-router connection is wasting address space. 

F. The broadcast domain in AREA 1 is too large for IP to function. 

Answer: ACE 


Q22. After the network has converged, what type of messaging, if any, occurs between R3 and R4? 


A. No messages are exchanged 

B. Hellos are sent every 10 seconds. 

C. The full database from each router is sent every 30 seconds. 

D. The routing table from each router is sent every 60 seconds. 

Answer: B 


Q23. An administrator is working with the 192.168.4.0 network, which has been subnetted with a /26 mask. Which two addresses can be assigned to hosts within the same subnet? (Choose two.) 

A. 192.168.4.61 

B. 192.168.4.63 

C. 192.168.4.67 

D. 192.168.4.125 

E. 192.168.4.128 

F. 192.168.4.132 

Answer: CD 


100-101  free practice questions

Renew ccent study guide 100-101:

Q24. Which two of the following are true regarding the configuration of RouterA? (Choose two.) 

A. At least 5 simultaneous remote connections are possible 

B. Only telnet protocol connections to RouterA are supported 

C. Remote connections to RouterA using telnet will succeed 

D. Console line connections will nevertime out due to inactivity 

E. Since DHCP is not used on Fa0/1 there is not a need to use the NAT protocol 

Answer: AC 


Q25. Which command is used to display the collection of OSPF link states? 

A. show ip ospf link-state 

B. show ip ospf lsa database 

C. show ip ospf neighbors 

D. show ip ospf database 

Answer: D 


Q26. What is the subnet address of 172.16.159.159/22? 

A. 172.16.0.0 

B. 172.16.128.0 

C. 172.16.156.0 

D. 172.16.159.0 

E. 172.16.159.128 

F. 172.16.192.0 

Answer: C 


100-101  free practice questions

Free ccent 100-101 cheat sheet:

Q27. Refer to the exhibit. 


After the power-on-self test (POST), the system LED of a Cisco 2950 switch turns amber. What is the status of the switch? 

A. The POST was successful. 

B. The switch has a problem with the internal power supply and needs an external power supply to be attached. 

C. POST failed and there is a problem that prevents the operating system from being loaded. 

D. The switch has experienced an internal problem but data can still be forwarded at a slower rate. 

E. The switch passed POST, but all the switch ports are busy. 

Answer: C 


Q28. Which transport layer protocol provides best-effort delivery service with no acknowledgment receipt required? 

A. HTTP 

B. IP 

C. TCP 

D. Telnet 

E. UDP 

Answer: E 


Q29. Refer to the exhibit. 


As packets travel from Mary to Robert, which three devices will use the destination MAC address of the packet to determine a forwarding path? (Choose three.) 

A. Hub1 

B. Switch1 

C. Router1 

D. Switch2 

E. Router2 

F. Switch3 

Answer: BDF 


Q30. Refer to the output of the corporate router routing table shown in the graphic. 


The corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. 

What will the router do with this packet? 

A. It will encapsulate the packet as Frame Relay and forward it out interface Serial 0/0.117. 

B. It will discard the packet and send an ICMP Destination Unreachable message out interface FastEthernet 0/0. 

C. It will forward the packet out interface Serial 0/1 and send an ICMP Echo Reply message out interface serial 0/0.102. 

D. It will change the IP packet to an ARP frame and forward it out FastEthernet 0/0. 

Answer: B 



see more 100-101 dumps