The Down to date Guide To 156-115.77 secret Dec 2016

100% Guarantee to Pass your 156-115.77 Exam, Each of our site have many totally free Check Point Check Point braindumps. As long as an individual follow the particular practice questions, you will obtain the Check Point Check Point certification. If you dont pass the particular 156-115.77 at your first attempt, you can get total refound within 30 days following checking the relevant data.Our Check Point Check Point certification education tests are created by the dedicated experts in line with the particular authoritative standards. We maintain high high quality and excellent value within our 156-115.77 training exam. We also make the review guide understandable and also un-demandingly implemented.

2016 Dec 156-115.77 exam answers

Q121. - (Topic 8) 

When troubleshooting a performance problem on multicore firewall that is using CoreXL, what command checks the number of connections each core is processing? 

A. sim affinity -l 

B. cat fwkern.conf 

C. fw CTL pstat 

D. fw ctl multik stat 

Answer:


Q122. - (Topic 8) 

The CoreXL software architecture includes the Secure Network Dispatcher (SND). One of the responsibilities of SND is to: 

A. Distribute non-accelerated packets among kernel instances 

B. Dispatch the packet securely through the VPN link 

C. Processing outgoing traffic from the network interfaces 

D. Dispatch the packet securely through the physical link 

Answer:


Q123. - (Topic 3) 

What would be a reason for changing the “Magic MAC”? 

A. To allow for automatic upgrades. 

B. To allow two or more cluster members to exist on the same network. 

C. To allow two or more clusters to exist on the same network. 

D. To allow the two cluster members to use the same virtual IP address. 

Answer:


Q124. - (Topic 4) 

You are experiencing an issue where Endpoint Connect client connects successfully however, it disconnects every 20 seconds. What is the most likely cause of this issue? 

A. The Accept Remote Access control connections is not enabled in Global Properties > FireWall Implied Rules. 

B. You have selected IKEv2 only in Global Properties > Remote Access > VPN – Authentication and Encryption. 

C. You are not licensed for Endpoint Connect client. 

D. Your remote access community is not configured. 

Answer:


Q125. - (Topic 6) 

If you need to use a Domain object in the Rule Base, where should this rule be located? 

A. No higher than the 2nd rule. 

B. The first rule in the Rule Base. 

C. The last rule before the clean up rule. 

D. The last rule after the clean up rule. 

Answer:


Leading 156-115.77 test engine:

Q126. - (Topic 3) 

With the default ClusterXL settings what will be the state of an active gateway upon using the command ClusterXL_admin up? 

A. Ready 

B. Down 

C. Standby 

D. Active 

Answer:


Q127. - (Topic 4) 

You are in VPN troubleshooting with a Partner and you suspect a mismatch configuration in Diffie-Hellman (DH) group to Phase1. After starting a vpn debug, in which packet would you look to analyze this option in your debug file? 

A. Packet3 

B. Packet4 

C. Packet5 

D. Packet1 

Answer:


Q128. - (Topic 9) 

You have strict IPS corporate guidelines. This is having a performance impact on the firewall. What steps could you take to minimize this impact without compromising the corporate policy? 

A. Select “Protect Internal hosts only” 

B. Select “Bypass IPS inspection when gateway is under heavy load” 

C. Select “Perform IPS inspection on all traffic” 

D. Without minimizing signatures you cannot improve performance 

Answer:


Q129. - (Topic 7) 

How does the Check Point Security Administrator enable NAT Templates? 

A. Run commands with syntax fw ctl set int cphwd_nat_templates_support 1 and fw ctl set int cphwd_nat_templates_enabled 1. 

B. Edit file $FWDIR/boot/modules/fwkern.conf with the lines “cphwd_nat_templates_support=1” and “cphwd_nat_templates_enabled=1”. 

C. Set Firewall object > NAT > Advanced 

D. Set Global properties > NAT-Network address translation 

Answer:


Q130. - (Topic 1) 

What flag option(s) must be used to dump the complete table in friendly format, assuming there are more than one hundred connections in the table? 

A. fw tab -t connections -f 

B. fw tab -t connect -f -u 

C. fw tab -t connections -s 

D. fw tab -t connections -f –u 

Answer:



see more 156-115.77 dumps