Passleader offers free demo for ccna 200 125 dumps exam. "CCNA Cisco Certified Network Associate CCNA (v3.0)", also known as ccna 200 125 study guide exam, is a Cisco Certification. This set of posts, Passing the Cisco ccna 200 120 vs 200 125 exam, will help you answer those questions. The 200 125 ccna v3 0 Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco ccna routing and switching 200 125 official cert guide library exams and revised by experts!
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/200-125-exam-dumps.html
P.S. High value 200-125 interactive bootcamp are available on Google Drive, GET MORE: https://drive.google.com/open?id=1IiiyEYVh7VGuzQjIt9B135ONv4m9W195
New Cisco 200-125 Exam Dumps Collection (Question 5 - Question 14)
Question No: 5
Which spanning-tree feature places a port immediately into a forwarding stated?
A. BPDU guard
B. PortFast
C. loop guard
D. UDLD
E. Uplink Fast
Answer: B
Explanation:
PortFast causes a switch or trunk port to enter the spanning tree forwarding state immediately, bypassing the listening and learning states.You can use PortFast on switch or trunk ports that are connected to a single workstation, switch, or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state.
Question No: 6
Which three technical services support cloud computing? (Choose three.)
A. Layer 3 network routing
B. redundant connections
C. extended SAN services
D. IP localization
E. VPN connectivity
Answer: B,C,D
Question No: 7
Refer to the exhibit.
Which statement describes the effect of this configuration?
A. The VLAN 10 VTP configuration is displayed.
B. VLAN 10 spanning-tree output is displayed.
C. The VLAN 10 configuration is saved when the router exits VLAN configuration mode.
D. VLAN 10 is added to the VLAN database.
Answer: D
Question No: 8
During which phase of PPPoE is PPP authentication performed?
A. the PPP Session phase
B. Phase 2
C. the Active Discovery phase
D. the Authentication phase
E. Phase 1
Answer: A
Question No: 9
If router R1 knows a static route to a destination network and then learn about the same destination network through a dynamic routing protocol, how does R1 respond?
A. It sends a withdrawal notification to the neighboring router.
B. It refuses to advertise the dynamic route to other neighbors.
C. It disables the routing protocol.
D. It prefers the static route.
Answer: D
Question No: 10
What is the best way to verify that a host has a path to other hosts in different networks?
A. Ping the loopback address.
B. Ping the default gateway.
C. Ping the local interface address.
D. Ping the remote network.
Answer: D
Explanation:
Ping is a tool that helps to verify IP-level connectivity; PathPing is a tool that detects packet loss over multiple-hop trips. When troubleshooting, thepingcommand is used to send an ICMP Echo Request to a target host name or IP address. Use Ping whenever you want to verify that a host computer can send IP packets to a destination host. You can also use the Ping tool to isolate network hardware problems and incompatible configurations.
If you callipconfig /alland receive a response, there is no need to ping the loopback address and your own IP address u2014 Ipconfig has already done so in order to generate the report.
It is best to verify that a route exists between the local computer and a network host by first using ping and the IP address of the network host to which you want to connect. The command syntax is:
ping <IP address>
Perform the following steps when using Ping:
u2711 Ping the loopback address to verify that TCP/IP is installed and configured correctly on the local computer.
ping 127.0.0.1
If the loopback step fails, the IP stack is not responding. This might be because the TCP drivers are corrupted, the network adapter might not be working, or another service is interfering with IP.
u2711 Ping the IP address of the local computer to verify that it was added to the network
correctly. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1.
ping<IP address of local host>
u2711 Ping the IP address of the default gateway to verify that the default gateway is functioning and that you can communicate with a local host on the local network.
ping<IP address of default gateway>
u2711 Ping the IP address of a remote host to verify that you can communicate through a router.
ping<IP address of remote host>
u2711 Ping the host name of a remote host to verify that you can resolve a remote host name.
ping<Host name of remote host>
u2711 Run a PathPing analysis to a remote host to verify that the routers on the way to the destination are operating correctly.
pathping<IP address of remote host>
Question No: 11
What is the correct routing match to reach 172.16.1.5/32?
A. 172.16.1.0/26
B. 172.16.1.0/25
C. 172.16.1.0/24
D. the default route
Answer: A
Question No: 12
Which NTP command configures the local device as an NTP reference clock source?
A. ntp peer
B. ntp broadcast
C. ntp master
D. ntp server
Answer: D
Question No: 13
Which condition does the err-disabled status indicate on an Ethernet interface?
A. There is a duplex mismatch.
B. The device at the other end of the connection is powered off.
C. The serial interface is disabled.
D. The interface is configured with theshutdowncommand.
E. Port security has disabled the interface.
F. The interface is fully functioning.
Answer: A
Question No: 14
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. It will encrypt all current and future passwords.
C. It will encrypt the secret password and remove the enable secret password from the configuration.
D. Only the enable secret password will be encrypted.
E. Only passwords configured after the command has been entered will be encrypted.
Answer: B
Explanation:
Enable vty, console, AUX passwords are configured on the Cisco device. Use the show run command to show most passwords in clear text. If the service password-encryption is used, all the passwords are encrypted. As a result, the security of device access is improved.
100% Up to the immediate present Cisco 200-125 Questions & Answers shared by Dumpscollection, Get HERE: http://www.dumpscollection.net/dumps/200-125/ (New 573 Q&As)