Want to know Examcollection ccie 400 101 Exam practice test features? Want to lear more about Cisco CCIE Routing and Switching (v5.0) certification experience? Study Tested Cisco 400 101 ccie answers to Improve 400 101 ccie questions at Examcollection. Gat a success with an absolute guarantee to pass Cisco passleader 400 101 (CCIE Routing and Switching (v5.0)) test on your first attempt.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 400-101 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 400-101 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/400-101-exam-dumps.html
Q151. Refer to the exhibit.
Which route type is displayed when you enter the command show ip route supernets-only on a device with this configuration?
A. Connected
B. OSPF
C. RIP
D. EIGRP
E. An empty route set
Answer: E
Explanation:
This command shows supernets only; it does not show subnets. In this case, the routing table would contain the 10.0.0.0/24 subnet, but not the 10.0.0.0/8 supernet.
Q152. DRAG DROP
Drag and drop the OSPF network type on the left to the correct category of timers on the right.
Answer:
Q153. Which authentication types does OSPF support?
A. null and clear text
B. MD5 only
C. MD5 and clear text
D. null, clear text, and MD5
E. clear text only
Answer: D
Q154. Which statement about NAT64 is true?
A. NAT64 provides address family translation and translates IPv4 to IPv6 and IPv6 to IPv4.
B. NAT64 provides address family translation and can translate only IPv6 to IPv4.
C. NAT64 should be considered as a permanent solution.
D. NAT64 requires the use of DNS64.
Answer: A
Q155. Refer to the exhibit.
A PE router is configured with a policy map that contains the policer shown. The policy map is configured in the inbound direction of an interface facing a CE router. If the PE router
receives 12Mb/s of traffic with the CoS value set to 7 on a 100-Mb/s interface from the CE router, what value of MPLS EXP is set when this traffic goes through the policer shown?
A. 0
B. 6
C. 7
D. 8
Answer: B
Explanation:
Here, the policer is set where the conforming traffic is set to 10 percent of the 100 Mbps interface, so anything more than 10 Mbps will be placed into the exceeding traffic class, the traffic EXP value will be changed from 7 to 6 per the configuration.
Q156. Refer to the exhibit.
Two multicast domains are configured as shown and connected with MSDP, but the two
domains are unable to communicate. Which two actions can you take to correct the problem? (Choose two.)
A. Change the peering IP address in AS 65220 to 10.0.0.20.
B. Change the peering AS on R2 to 65210.
C. Verify that UDP port 639 is open.
D. Verify that TCP port 139 is open.
E. Change the MSDP originator-id to GigabitEthernet 0/0/0 on both routers.
F. Change the MSDP peering IP address on R2 to 172.16.1.13.
Answer: A,B
Q157. Which command drops packets with unknown source addresses until you remove a sufficient number of secure MAC addresses to drop below the maximum value, and also causes the Security Violation counter to increment?
A. switchport port-security violation protect
B. switchport port-security violation drop
C. switchport port-security violation shutdown
D. switchport port-security violation restrict
Answer: D
Explanation:
When configuring port security violation modes, note the following information:
. protect—Drops packets with unknown source addresses until you remove a sufficient number of secure MAC addresses to drop below the maximum value.
. restrict—Drops packets with unknown source addresses until you remove a sufficient number of secure MAC addresses to drop below the maximum value and causes the SecurityViolation counter to increment.
. shutdown—Puts the interface into the error-disabled state immediately and sends an SNMP trap notification.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/port_sec.html
Q158. Which Cisco IOS XE process administers routing and forwarding?
A. Forwarding manager
B. Interface manager
C. Cisco IOS
D. Host manager
Answer: C
Explanation:
Some of the processes are listed in the table below:
Process
Purpose
Affected FRUs
SubPackage Mapping
Host Manager
Provides an interface between the IOS process and many of the information-gathering functions of the underlying platform kernel and operating system.
RP (one instance per RP)
SIP (one instance per SIP)
ESP (one instance per ESP)
RPControl
SIPBase
ESPBase
Interface Manager
Provides an interface between the IOS process and the per-SPA interface processes on the SIP.
RP (one instance per RP)
SIP (one instance per SIP)
RPControl
SIPBase
IOS
The IOS process implements all forwarding and routing features for the router.
RP (one per software redundancy instance per RP). Maximum of two instances per RP.
RPIOS
Forwarding Manager
Manages the downloading of configuration to each of the ESPs and the communication of forwarding plane information, such as statistics, to the IOS process.
RP (one per software redundancy instance per RP). Maximum of two instances per RP.
ESP (one per ESP)
RPControl
ESPBase
Reference: http://www.cisco.com/c/en/us/td/docs/routers/asr1000/configuration/guide/chassis/asrswcfg /Software_Packaging_Architecture.html
Q159. Which three options must be configured when deploying OSPFv3 for authentication? (Choose three.)
A. security parameter index
B. crypto map
C. authentication method
D. IPsec peer
E. encryption algorithm
F. encryption key
G. IPsec transform-set
H. authentication key
Answer: A,C,H
Q160. DRAG DROP
Drag and drop the IPv6 multicast feature or protocol on the left to the correct address space on the right.
Answer:
