Cause all that matters here is passing the IBM C9010-022 exam. Cause all that you need is a high score of C9010-022 IBM AIX Administration V1 exam. The only one thing you need to do is downloading Exambible C9010-022 exam study guides now. We will not let you down with our money-back guarantee.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for IBM C9010-022 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW C9010-022 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/C9010-022-exam-dumps.html
Q141. - (Topic 3)
How can a system administrator verify the progress of an AIX 7.1 client installation from the NIM master?
A. nim -status
B. Isnim-I
C. nim-o check
D. tail-f/var/adrn/ras/nimclient
Answer: B
Q142. - (Topic 4)
An administrator attempts to install the fileset tivoli.tsm.client, but it fails due to missing requisites.
The administrator copies the required filesets into the install directory and tries the preview install again. It fails with the same results, as shown in the graphic below.
What must the administrator do to successfully install the filesets?
A. Remove the .toe file or run inutoc.
B. Provide the correct version of xlsmp.rte.
C. Make the permissions of all of the filesets group executable
D. Make the permissions of the requisite filesets group readable
Answer: A
Q143. - (Topic 4)
An AIX instance was initially configured to communicate over a single network interface. The administrator plans to configure an EtherChannel using the existing network interface and an additional network interface.
Which is the correct sequence of steps to implement this configuration?
A. Remove the existing IP information Add both interfaces as primary adapters Configure the IP address
B. Configure the existing interface as a primary adapter Configure the additional interface as a backup adapter
C. Configure the same IP address on the additional interface Add both adapters as primary adapters Remove the existing default route
D. Add both adapters as primary adapters Configure the IP address as an alias on the additional interface
Answer: A
Q144. - (Topic 1)
An administrator notices that the ntp group subsystem is not starting up at boot time. What will cause this issue?
A. The /etc/ntp.conf file has the following line commented out broadcastserver
B. The following line is commented outinthe/etc/inetd.conf file: ntp 123/tcp # Network Time Protocol
C. The following line is commented out of the /etc/inittab file: xntpd: 23456789:respawn:/usr/sbin/xntpd > /dev/console 2>&1 #Start ntp daemon
D. The /etc/rc.tcpip file has the following line commented out: start /usr/sbin/xntpd "$src_running"
Answer: D
Q145. - (Topic 2)
The AIX hosts node1 and node2 have Ethernet adapters, both named ent0, configured on the same network. Both are dedicated physical 1GB adapter ports in a Host Ethernet
Adapter. Based on this information and the output shown for each node, what is the most likely cause of intermittent failures and slow communication between these adapters?
A. The jumbo_frarnes setting is 'no' and should be set to 'yes'.
B. The Multi-Core Scaling mode is enabled. Multi-Core Scaling is interfering with communications because the processor is too busy.
C. The Shared Ethernet Adapter does not have enough bandwidth to accommodate the network traffic.
D. The media speed is set differently on the adapters than the endpoints on the switch.
Answer: D
Q146. - (Topic 3)
Based on the following output, what must be done if loglv1 name is changed to db2loglv?
A. Run the chfs command to update /exportfs/db01 logging logical volume to db2loglv.
B. Run the logform command to update the log format of db2loglv.
C. Run the chlv command to update dblv01 logging logical volume to db2loglv.
D. Run the chvg command to update volume group default logging logical volume to db2loglv.
Answer: C
Q147. - (Topic 3)
A new naming guideline requires the existing volume group, db2vg on hdisk1, be renamed
to db2logsvg01. Which command sequence will accomplish this with the least downtime?
A. varyoffvg db2vg exportvg db2vg importvg -y db2logsvg01 hdisk1
B. odmupdate -q VGNAME db2vg db2logsvg01 sync db2vg db2logsvg01 varyonvg db2logsvg01 hdisk1
C. varyoffvg db2vg chvg -a name db2vg db2logsvg01 varyonvg db2vg hdisk1
D. savevg db2vg rmvg db2vg mkvg -y db2logsvg0l hdisk1 restvg hdisk1
Answer: A
