Oct 2016 updated: ccna icnd2 pdf free download

Proper study guides for Latest Cisco Interconnecting Cisco Networking Devices Part 2 (ICND2) certified begins with Cisco 200-101 preparation products which designed to deliver the Virtual 200-101 questions by making you pass the 200-101 test at your first time. Try the free 200-101 demo right now.

2016 Oct ccent icnd2:

Q51. Refer to the exhibit. 


Why has this switch not been elected the root bridge for VLAN1? 

A. It has more than one interface that is connected to the root network segment. 

B. It is running RSTP while the elected root bridge is running 802.1d spanning tree. 

C. It has a higher MAC address than the elected root bridge. 

D. It has a higher bridge ID than the elected root bridge. 

Answer: D 


Q52. Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.) 

A. Router(config)# router ospf 0 

B. Router(config)# router ospf 1 

C. Router(config)# router ospf area 0 

D. Router(config-router)# network 192.168.16.0 0.0.0.255 0 

E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0 

F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0 

Answer: BE 


Q53. What can be done to Frame Relay to resolve split-horizon issues?(Choose two.) 

A. Disable Inverse ARP. 

B. Create a full-mesh topology. 

C. Develop multipoint subinterfaces. 

D. Configure point-to-point subinterfaces. 

E. Remove the broadcast keyword from the frame-relay map command. 

Answer: BD 


Q54. Refer to the exhibit. 


Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1? 

A. The router will forward packets from R3 to R2 to R1. 

B. The router will forward packets from R3 to R1 to R2. 

C. The router will forward packets from R3 to R2 to R1 AND from R3 to R1. 

D. The router will forward packets from R3 to R1. 

Answer: C 


Q55. What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.) 

A. They create split-horizon issues. 

B. They require a unique subnet within a routing domain. 

C. They emulate leased lines. 

D. They are ideal for full-mesh topologies. 

E. They require the use of NBMA options when using OSPF. 

Answer: BC 


200-101 sample question

Improved ccna vs icnd1 and icnd2:

Q56. Which two options are valid WAN connectivity methods? (Choose two.) 

A. PPP 

B. WAP 

C. DSL 

D. L2TPv3 

E. Ethernet 

Answer: AC 


Q57. Which statements are true about EIGRP successor routes? (Choose two.) 

A. A successor route is used by EIGRP to forward traffic to a destination. 

B. Successor routes are saved in the topology table to be used if the primary route fails. 

C. Successor routes are flagged as 'active' in the routing table. 

D. A successor route may be backed up by a feasible successor route. 

E. Successor routes are stored in the neighbor table following the discovery process. 

Answer: AD 


Q58. Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications? 

A. RSA 

B. L2TP 

C. IPsec 

D. PPTP 

Answer: C 


Q59. What is one benefit of PVST+? 

A. PVST+ supports Layer 3 load balancing without loops. 

B. PVST+ reduces the CPU cycles for all the switches in the network. 

C. PVST+ allows the root switch location to be optimized per VLAN. 

D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage. 

Answer: C 


Q60. R1 is configured with the default configuration of OSPF. 

From the following list of IP addresses configured on R1, which address will the OSPF process select as the router ID? 



A. 192.168.0.1 

B. 172.16.1.1 

C. 172.16.2.1 

D. 172.16.2.225 

Answer: A



see more 200-101 dumps