Amazing 200 125 ccna book To Try

Cause all that matters here is passing the Cisco ccna 200 125 pdf exam. Cause all that you need is a high score of ccna 200 125 syllabus CCNA Cisco Certified Network Associate CCNA (v3.0) exam. The only one thing you need to do is downloading Testking ccna 200 125 torrent exam study guides now. We will not let you down with our money-back guarantee.


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/200-125-exam-dumps.html

P.S. Virtual 200-125 torrent are available on Google Drive, GET MORE: https://www.slideshare.net/reinigerodp/certleader-200-125examquestionsmaterials


New Cisco 200-125 Exam Dumps Collection (Question 7 - Question 14)

Q7. What will be the result if the following configuration commands are implemented on a Cisco switch?

Switch(config-if)# switchport port-security

Switch(config-if)# switchport port-security mac-address sticky

A. A dynamically learned MAC address is saved in the startup-configuration file.

B. A dynamically learned MAC address is saved in the running-configuration file.

C. A dynamically learned MAC address is saved in the VLAN database.

D. Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.

E. Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.

Answer: B

Explanation:

In the interface configuration mode, the command switchport port-security mac-address sticky enables sticky learning. When entering this command, the interface converts all the dynamic secure MAC addresses to sticky secure MAC addresses.


Q8. Refer to the exhibit.

Statements A, B, C, and D of ACL 10 have been entered in the shown order and applied to interface E0 inbound, to prevent all hosts (except those whose addresses are the first and last IP of subnet 172.21.1.128/28) from accessing the network. But as is, the ACL does not restrict anyone from the network. How can the ACL statements be re-arranged so that the system works as intended?

A. ACDB

B. BADC

C. DBAC

D. CDBA

Answer: D

Explanation:

Routers go line by line through an access list until a match is found and then will not look any further, even if a more specific of better match is found later on in the access list. So, it it best to begin with the most specific entries first, in this cast the two hosts in line C and D. Then, include the subnet (B) and then finally the rest of the traffic (A).


Q9. Refer to the exhibit.

A network administrator attempts to ping Host2 from Host1 and receives the results that are shown. What is the problem?

A. The link between Host1 and Switch1 is down.

B. TCP/IP is not functioning on Host1

C. The link between Router1 and Router2 is down.

D. The default gateway on Host1 is incorrect.

E. Interface Fa0/0 on Router1 is shutdown.

F. The link between Switch1 and Router1 is down.

Answer: C

Explanation:

Host1 tries to communicate with Host2. The message destination host unreachable from Router1 indicates that the problem occurs when the data is forwarded from Host1 to Host2. According to the topology, we can infer that the link between Router1 and Router2 is down.


Q10. What are the Populardestinations for syslog messages to be saved? (Choose three)

A. Flash

B. The logging buffer .RAM

C. The console terminal

D. Other terminals

E. Syslog server

Answer: B,C,E

Explanation:

By default, switches send the output from system messages and debug privileged EXEC commands to a logging process. The logging process controls the distribution of logging messages to various destinations, such as the logging buffer (on RAM), terminal lines (console terminal), or a UNIX syslog server, depending on your configuration. The process also sends messages to the console.

Note: Syslog messages can be written to a file in Flash memory although it is not a popular place to use. We can configure this feature with the commandlogging file flash:filename.


Q11. Refer to the exhibit.

Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.)

A. The cable that is connected to S0/0 on RouterA is faulty.

B. Interface S0/0 on RouterB is administratively down.

C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.

D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.

E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.

F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.

Answer: E,F

Explanation:

From the output we can see that there is a problem with the Serial 0/0 interface. It is enabled, but the line protocol is down. There could be a result of mismatched encapsulation or the interface not receiving a clock signal from the CSU/DSU.


Q12. How does using the service password-encryption command on a router provide additional security?

A. by encrypting all passwords passing through the router

B. by encrypting passwords in the plain text configuration file

C. by requiring entry of encrypted passwords for access to the device

D. by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges

E. by automatically suggesting encrypted passwords for use in configuring the router

Answer: B

Explanation:

By using this command, all the (current and future) passwords are encrypted. This command is primarily useful for keeping unauthorized individuals from viewing your password in your configuration file


Q13. Refer to the exhibit.

Which rule does the DHCP server use when there is an IP address conflict?

A. The address is removed from the pool until the conflict is resolved.

B. The address remains in the pool until the conflict is resolved.

C. Only the IP detected by Gratuitous ARP is removed from the pool.

D. Only the IP detected by Ping is removed from the pool.

E. The IP will be shown, even after the conflict is resolved.

Answer: A

Explanation:

An address conflict occurs when two hosts use the same IP address. During address assignment, DHCP checks for conflicts using ping and gratuitous ARP. If a conflict is detected, the address is removed from the pool. The address will not be assigned until the administrator resolves the conflict.

(Reference: http://www.cisco.com/en/US/docs/ios/12_1/iproute/configuration/guide/1cddhcp.html)


Q14. CORRECT TEXTCCNA.com has a small network that is using EIGRP as its IGP. All routers should be running an EIGRP AS number of 12. Router MGT is also running static routing to the ISP.

CCNA.com has recently added the ENG router. Currently, the ENG router does not have connectivity to the ISP router. All over interconnectivity and Internet access for the existing locations of the company are working properly.

The taskis to identify the fault(s) and correct the router configuration(s) to provide full connectivity between the routers.

Access to the router CLI can be gained by clicking on the appropriate host.

All passwords on all routers arecisco.

IP addresses are listed in the chart below.

MGT

Fa0/0 u2013 192.168.77.33

S1/0 u2013 198.0.18.6

S0/0 u2013 192.168.27.9

S0/1 u2013 192.168.50.21

ENG

Fa0/0 u2013 192.168.77.34

Fa1/0 u2013 192.168.12.17

Fa0/1 u2013 192.168.12.1

Parts1

Fa0/0 u2013 192.168.12.33

Fa0/1 u2013 192.168.12.49

S0/0 u2013 192.168.27.10

Parts2

Fa0/0 u2013 192.168.12.65

Fa0/1 u2013 192.168.12.81

S0/1 u2013 192.168.50.22

Answer:

On the MGT Router: Config t

Router eigrp 12

Network 192.168.77.0


100% Update Cisco 200-125 Questions & Answers shared by 2passeasy, Get HERE: https://www.2passeasy.com/dumps/200-125/ (New 890 Q&As)