Cause all that matters here is passing the Cisco cisco 300 101 dump exam. Cause all that you need is a high score of route 300 101 ROUTE Implementing Cisco IP Routing exam. The only one thing you need to do is downloading Exambible 300 101 exam exam study guides now. We will not let you down with our money-back guarantee.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 300-101 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 300-101 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/300-101-exam-dumps.html
P.S. Top Quality 300-101 cram are available on Google Drive, GET MORE: https://drive.google.com/open?id=1lWZpAR5vb8lOApmzhHWMzXffOPhCR-LL
New Cisco 300-101 Exam Dumps Collection (Question 14 - Question 23)
New Questions 14
Which two OSPF network types can operate without a DR/BDR relationship? (Choose Two)
A. Point-to-multipoint
B. Point-to-point
C. nonbroadcast
D. nonbroadcast multi-access
E. broadcast
Answer: A,B
New Questions 15
Which three IP SLA performance metrics can you use to monitor enterprise-class networks? (Choose three.)
A. PAcket loss
B. Delay
C. bandwidth
D. Connectivity
E. Reliability
F. traps
Answer: A,B,D
New Questions 16
The following configuration is applied to a router at a branch site:
ipv6 dhcp pool dhcp-pool dns-server 2001:DB8:1:B::1
dns-server 2001:DB8:3:307C::42 domain-name example.com
!
If IPv6 is configured with default settings on all interfaces on the router, which two dynamic IPv6 addressing mechanisms could you use on end hosts to provide end-to-end connectivity? (Choose two.)
A. EUI-64
B. SLAAC
C. DHCPv6
D. BOOTP
Answer: A,B
New Questions 17
Refer to the exhibit. The network setup is running the RIP routing protocol. Which two events will occur following link failure between R2 and R3? (Choose two.)
A. R2 will advertise network 192.168.2.0/27 with a hop count of 16 to R1.
B. R2 will not send any advertisements and will remove route 192.168.2.0/27 from its routing table.
C. R1 will reply to R2 with the advertisement for network 192.168.2.0/27 with a hop count of 16.
D. After communication fails and after the hold-down timer expires, R1 will remove the 192.168.2.0/27 route from its routing table.
E. R3 will not accept any further updates from R2, due to the split-horizon loop prevention mechanism.
Answer: A,C
New Questions 18
Refer to the exhibit.
Which command allows hosts that are connected to FastEthernet0/2 to access the Internet?
A. ip nat inside source list 10 interface FastEthernet0/1 overload
B. ip nat outside source static 209.165.200.225 10.10.10.0 overload
C. ip nat inside source list 10 interface FastEthernet0/2 overload
D. ip nat outside source list 10 interface FastEthernet0/2 overload
Answer: A
New Questions 19
Which option is the first task that a device that is configured with NAT64 performs when it receives an incoming IPv6 packet that matches the stateful NAT64 prefix?
A. It translates the IPv6 header into an IPv4 header.
B. It checks the IPv6 packet against the NAT64 stateful prefix.
C. It translates the IPv6 source address to an IPv4 header.
D. It translates the^ IPv4 destination address into a new NAT64 state.
E. It performs an IPv6 route lookup.
Answer: A
New Questions 20
Which two statements about EVN are true? (Choose two)
A. Virtual network tags are assigned per-VRF.
B. it is supported only on access ports.
C. Virtual network tags are assigned globally.
D. Routing metrics can be manipulated only from directly within the routing-context configuration.
E. The VLAN ID in the 802.1q frame carries the virtual network tag.
F. The VLAN ID is the ISL frame carries the virtual network tag.
Answer: A,E
New Questions 21
Considering the IPv6 address independence requirements, which process do you avoid when you use NPTv6 for translation?
A. rewriting of higher layer information
B. checksum verification
C. ipv6 duplication and conservation
D. IPSEC AH header modification
Answer: A
New Questions 22
Which NAT Command to disable dynamic ARP learning on an interface?
A. R(config-if) # ip nat enable
B. R(config-if) # ip nat inside
C. R(config-if)# ip nat outside
D. R(config)# ip nat service
E. R(config)# ip nat allow static host
Answer: E
New Questions 23
Exhibit:
Refer to the exhibit showing complete command output. What type of OSPF router is Router A?
A. internal router
B. ASBR
C. ABR
D. edge router
Answer: C
Explanation: An area is interface specific. A router that has all of its interfaces within the same area is called an internal router (IR). A router that has interfaces in multiple areas is called an area border router (ABR).
http://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/7039-1.html#t8
Recommend!! Get the Top Quality 300-101 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/300-101/ (New 436 Q&As Version)
