Our pass rate is high to 98.9% and the similarity percentage between our 9tut ccnp 300 101 study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco ccnp route 300 101 pdf exam in just one try? I am currently studying for the Cisco route 300 101 exam. Latest Cisco 300 101 dumps Test exam practice questions and answers, Try Cisco ccnp 300 101 Brain Dumps First.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 300-101 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 300-101 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/300-101-exam-dumps.html
P.S. High value 300-101 braindumps are available on Google Drive, GET MORE: https://drive.google.com/open?id=1g3xBE0KhVLL-l1SXbBZMbJhQ4SK2THNQ
New Cisco 300-101 Exam Dumps Collection (Question 15 - Question 23)
Question No: 15
Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?
A. unicast IPv6 addresses
B. link-local addresses
C. multicast address FF02::5
D. unicast IPv4 addresses
Answer: C
Question No: 16
What is the optimal location from which to execute a debug command that produces an excessive amount of information?
A. Vty lines
B. SNMP commands
C. A console port
D. An AUX port
Answer: A
Question No: 17
What are two options for authenticating a user who is attempting to access a network
device? (Choose Two)
A. RADIUS
B. 802.1x
C. CHAP
D. TACACS+
E. PAP
Answer: A,D
Question No: 18
Which three statements about configuring OSPF in a IPv6 network are true? (Choose three.)
A. OSPF version 2 will support IPv6.
B. OSPF version 3 will support IPv6.
C. Multiple instances of OSPF for IPv6 can be run on a link.
D. Networks must be explicitly configured using the network command in router OSPF configuration mode.
E. IPv4 addresses cannot be used as the router ID in OSPF for IPv6.
F. The interface command ipv6 ospf <process-id> area <area-id> is all that is required to enable OSPF for IPv6 on an interface.
Answer: B,C,F
Question No: 19
Using new backup router in spite of faulty one in ospf domain but relationship with neighbour in one interface only not working , what is the reason of this problem?(choose 2)
A. area Id mismatch
B. authentication mismatch
C. process id of ospf not match
D. ospf timers not match
Answer: A,B
Question No: 20
Which command must be globally enabled on a Cisco router to support IPv6?
A. ip routing ipv6
B. ipv6 unicast-routing
C. ipv6 routing
D. ip classless
E. ipv6 cef
Answer: B
Question No: 21
Refer to the exhibit. Which statement about the command output is true?
A. The router exports flow information to 10.10.10.1 on UDP port 5127.
B. The router receives flow information from 10.10.10.2 on UDP port 5127.
C. The router exports flow information to 10.10.10.1 on TCP port 5127.
D. The router receives flow information from 10.10.10.2 on TCP port 5127.
Answer: A
Question No: 22
Refer to the exhibit. What two statements are true? (Choose two.)
A. Interface FastEthernet 0/0 was configured with the ipv6 ospf 1 area 1 command.
B. OSPF version 2 has been enabled to support IPv6.
C. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
D. The output was generated by the show ip interface command.
E. The router was configured with the commands: router ospf 1 network 172.16.6.0
0.0.0.255 area 1
F. This is the designated router (DR) on the FastEthernet 0/0 link.
Answer: A,C
Explanation:
OSPFv3 supports IPv6. The configuration of OSPFv3 is not a subcommand mode of the router ospf command as it is in OSPFv2 configuration. For example, instead of using the network area command to identify networks that are part of the OSPFv3 network, the interfaces are directly configured to specify that IPv6 networks are part of the OSPFv3 network.
The following describes the steps to configure OSPF for IPv6:
There are several commonly used OSPFv3 show commands, including the show ipv6 ospf [process-id] [area-id] interfacee [interface] command.
Question No: 23
Refer to the exhibit.
The 6to4 overlay tunnel configuration has been applied on each router to join isolated IPv6 networks over a IPv4 network. Which statements regarding the 6to4 overlay tunnel is true?
A. The least significant 32 bits in the address referenced by the ipv6 route 2002::/16 Tunnel0 command will correspond to the interface E0/0 IPv4 address
B. The least significant 32 bits in the address referenced by the ipv6 route 2002::/16 Tunnel0 command will correspond to the IPv4 address assigned to the tunnel source
C. The configuration is invalid since the tunnel source command must be configured with an IPv6 address
D. This is actually a configuration example of an IPv4-compatible tunnel and not a 6to4 tunnel
E. This is actually a configuration example of an ISATAP overlay tunnel and not a 6to4 tunnel
Answer: B
Explanation:
6to4 tunnels use IPv6 addresses that concatenate 2002::/16 with the 32-bit IPv4 address of the edge router, creating a 48-bit prefix. The tunnel interface on R1 has an IPv6 prefix of 2002:4065:4001:1::/64, where 4065:4001 is the hexadecimal equivalent of 64.101.64.1, the IPv4 address of its interface in the IPv4 network. The tunnel interface on R2 has an IPv6 prefix of 2002:4065:4101:1::/64, where 4065:4101 is the hexadecimal equivalent of 64.101.65.1, the IPv4 address of its interface in the IPv4 network.
When R1 receives a packet with IPv6 destination address of 2002:4065:4101:1:: (from the left IPv6 network, for example) R1 will:
* Take the IPv6 destination address of that packet (2002:4065:4101:1::) and convert it into
an IPv4 address. In this case, the IPv4 address is 40.65.41.01 in hexa, which is 64.101.65.1 in decimal format.* R1 encapsulates the IPv6 packet in an IPv4 packet with a destination address of 64.101.65.1; the packet is routed normally through the IPv4 network to R2* R2 receives the IPv4 packet, decapsulates and routes it normally to its final IPv6 destination.
Recommend!! Get the High value 300-101 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/300-101/ (New 487 Q&As Version)
