Exact 300-165 Answers 2021

NEW QUESTION 1
How does addition of bandwidth between spine and leaf switches in a FabricPath architecture get utilized?

• A. Links between the same set of switches are automatically added to a port channel.
• B. Adding additional bandwidth is handled dynamically using the 802.1AX protocol.
• C. Traffic is load shared automatically across the available paths to the destination.
• D. FabricPath uses hardware bonding of physical interfaces to form higher-speed link

Answer: C

NEW QUESTION 2
Refer to the exhibit.

Which statement based on these two outputs that were collected 24 hours apart is true?

• A. The Site 2 OTV edge device has gone down.
• B. The MAC address cannot be discovered on two separate port channel interfaces.
• C. The MAC address that ends in 020a moved to the local site 23 hours ago.
• D. The Overlay1 IP address should be a multicast IP addres

Answer: C

NEW QUESTION 3
You have a Switch that is operating NPV mode. The interfaces of the switch use which port type to connect to the core network?

• A. TE Port
• B. NP Port
• C. E Port
• D. F Port

Answer: B

NEW QUESTION 4
Refer to the exhibit.

What is the effect of the bind interface eth 1/16 command on the vfc 130 interface?

• A. It transitions the port to the forwarding state of the spanning tree automatically.
• B. It attaches the FCoE interface to the VSAN interface.
• C. It attaches the virtual Fibre Channel interface to the physical interface.
• D. It attaches the physical Fibre Channel interface to the virtual Fibre Channel interfac

Answer: C

NEW QUESTION 5
Which command configures the aging time for VLAN 100 to 50 minutes?

• A. mac address-table aging-time 3000 vlan 100
• B. mac address-table aging-time 50
• C. mac address-table aging-time 300
• D. mac address-table aging-time 50 vlan 100

Answer: A

NEW QUESTION 6
You are implementing a Cisco Fabric Path network. Which statement accurately describes the VNSegment feature?

• A. The VN-Segment feature must be enabled on all leaf switches.
• B. Up to 16,000 VN segments are supported on a leaf switch.
• C. The VN-Segment feature must be enabled on all switches.
• D. The VN-Segment tag is added to VN-Segment edge port

Answer: A

NEW QUESTION 7
Assuming hello PDU authentication has been disabled, which command re-enables the feature on a FabricPath interface?

• A. switch (config-if) # fabricpath isis authentication-type cleartext
• B. switch (config-if) # fabricpath isis authentication-type md5
• C. switch (config-if) # fabricpath isis authentication check
• D. switch (config-if) # fabricpath isis hello-interval

Answer: C

NEW QUESTION 8
Which two functions are enabled when you set up vPC+ at the FabricPath edge? (Choose two.)

• A. the ability to attach Cisco Fabric Extenders in FEX active/active mode
• B. the ability to stop all Layer 3 egress traffic
• C. the ability to attach servers to edge switches with port-channel teaming
• D. the ability to attach additional Classic Ethernet switches in vPC+ mode

Answer: AC

NEW QUESTION 9
Which statement about implementation of Cisco TrustSec on Cisco Nexus 5546 or 5548 switches are true?

• A. Cisco TrustSec support varies depending on Cisco Nexus 5500 Series Switch model.
• B. The hardware is not able to support MACsec switch-port-level encryption based on IEEE 802.1AE.
• C. The maximum number of RBACL TCAM user configurable entries is 128k.
• D. The SGT Exchange Protocol must use the management (mgmt 0) interface.

Answer: B

Explanation:
Reference:
https://scadahacker.com/library/Documents/Manuals/Cisco%20-%20TrustSec%20Solution%20Overview.pdf

NEW QUESTION 10
Within the vPC configuration of the 7K's the command peer-gateway is configured as confirmed with the command show vpc. what is the result of enabling this command?

• A. Enable 7k-3 to act as the active gateway for packet received on VLAN 101 that are addressed to the MAC address of 7k-4
• B. Enables n7k-4 to use of the vpc peer link for forwarding packets received on VLAN 100 that are addressed to the MACRESS OF 7K-4
• C. Generates IP redirect messages for packet switched though the peer-gateway router
• D. Cause the HSRP active router to update the ARP table on the standby router for faster convergence after the vPC peer link has flapped
• E. Allow the vpc peers to coordinate the IACP ID with must be the same on all links on all the port channel.

Answer: D

Explanation:
The vPC peer gateway command allows either Nexus 7000 to intercept any packet (including HSRP packets) which is destined to the other peer’s MAC address to prevent the packet from traversing the vPC peer link.

NEW QUESTION 11
Which three items must be configured in the port profile client in Cisco UCS Manager? (Choose three.)

• A. port profile
• B. DVS
• C. data center
• D. folder
• E. vCenter IP address
• F. VM port group

Answer: BCD

Explanation:
After associating an ESX host to a DVS, you can migrate existing VMs from the vSwitch to the DVS, and you can create VMs to use the DVS instead of the vSwitch. With the hardware-based VN-Link implementation, when a VM uses the DVS, all VM traffic passes through the DVS and ASIC-based switching is performed by the fabric interconnect.
In Cisco UCS Manager, DVSes are organized in the following hierarchy: vCenter
Folder (optional) Datacenter Folder (required) DVS
At the top of the hierarchy is the vCenter, which represents a VMware vCenter instance. Each vCenter contains one or more datacenters, and optionally vCenter folders with which you can organize the
datacenters. Each datacenter contains one or more required datacenter folders. Datacenter folders contain the DVSes.
Reference: http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/1-3-
1/b_UCSM_GUI_Configuration_Guide_1_3_1/UCSM_GUI_Configuration_Guide_1_3_1_chapter28.h tml

NEW QUESTION 12
Refer to the exhibit.

Which statement about the configuration is true?

• A. It provides an authoritative LISP site for IPv6 EID prefix 2110 cc8 a /48.
• B. It configures a single map resolver system.
• C. It creates a LISP site policy that requires active/standby service provider links for ingress traffic.
• D. It configures PxTR services for IPv6 EID prefix 2110:ccB:a::/48.

Answer: A

NEW QUESTION 13
Ethernet interface 1/5 on Cisco Nexus 5548 is connected to Cisco UCS C220 rack server. What is the status of Ethernet 1/5 interface for FCoE functionality?

• A. Interface reset on Ethernet 1/5 is preventing the FCoE connection from coming up
• B. MTU size of 1500 on Ethernet interface 1/5 needs to be changed for FCoE to come UP
• C. Cisco Nexus 5548 needs a layer 3 daughter card for FCoE to come UP on the Ethernet interface 1/5
• D. Ethernet interface 1/5 is operational for FCoE and the status is UP

Answer: D

NEW QUESTION 14
Which implicit rules are applied to all IPv6 ACLs?

• A. deny icmp any any nd-na deny icmp any any nd-nspermit icmp any any router-advertisement permit icmp any any router-solicitation deny ipv6 any any
• B. deny icmp any any nd-na log deny icmp any any nd-ns log deny ipv6 any any log
• C. deny icmp any any router-advertisement log deny icmp any any router-solicitation log deny ipv6 any any log
• D. permit icmp any any nd-na permit icmp any any nd-nspermit icmp any any router-advertisement permit icmp any any router-solicitation deny ipv6 any any

Answer: D

NEW QUESTION 15
Refer to the exhibit.

What does the diameter command specify?

• A. the maximum number of hops between any two bridges on a network.
• B. the number of VLANs that were removed from the MSTI.
• C. the VLAN that becomes the root of the MSTI
• D. the maximum number of hops between any two MST instances on a network

Answer: A

NEW QUESTION 16
DRAG DROP
Drag and drop the types of PTP clocks on the left to their correct descriptions on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 17
Which statement accurately describes MP-BGP EVPN?

• A. MP-BGP EVPN is a Layer 3 overlay alternative to VXLANs.
• B. The control plane of the VXLAN overcomes the flood-and-learn limitations of MP-BGP EVPN.
• C. The MP-BGP EVPN control plane overcomes the flood-and-learn limitations of the VXLAN.
• D. MP-BGP EVPN is a Layer 2 overlay alternative to VXLAN

Answer: C

NEW QUESTION 18
DRAG DROP
Drag the description on the left to the most appropriate Nexus product on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 19
Which two actions are required before FIPS is configured in Cisco MDS? (Choose two.)

• A. Passwords must be a minimum of 10 characters in length.
• B. SNMP v2 or v3 must be enabled.
• C. Remote authentication must occur utilizing RADIUS/TACACS+.
• D. Disable VRRP.
• E. Delete all SSH server RSA key pairs.
• F. Delete all IKE policies utilizing MD5 or DES for encryption.
• G. Enable the FC-FIPS feature.
• H. Disable SS

Answer: DF

NEW QUESTION 20
Which statement describes what happens if a new EPLD version is released with a new Cisco NX-OS version for a Cisco Nexus switch, but these EPLDs are not upgraded at the same time that NX-OS is upgraded?

• A. Any new hardware or software feature that depends on the updated EPLD image is disabled until upgraded.
• B. Modules that use an updated EPLD image remain offline until the EPLD is upgraded.
• C. The EPLD image version mismatch is detected by the supervisor, which automatically initiates an upgrade.
• D. The Cisco NX-OS upgrade fails as a result of the mismatch between EPLDs and NX-OS version

Answer: A

NEW QUESTION 21
Refer to the exhibit.

Which statement about the NetFlow implementation is true?

• A. It samples inbound IPv6 traffic on Ethernet 2/1
• B. It uses TCP for data export.
• C. It samples outbound traffic on Ethernet 2/1
• D. It samples inbound traffic on Ethernet 2/1

Answer: D

Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/fnetflow/configuration/15-mt/fnf-15-mtbook/use-fnflow-redce-cpu.html

NEW QUESTION 22
Using the default VDC high-availability options in the Cisco Nexus 7010 switch, which event occurs after a VDC failure?

• A. VDC restart occurs.
• B. The VDC is deleted.
• C. VDC bringdown occurs, and the VDC must be restarted manually.
• D. VDC shutdown occurs, and the VDC must be restarted manuall

Answer: D

NEW QUESTION 23
DRAG DROP
You must configure NetFlow on a Cisco Nexus 7000 Series switch Drag and drop the configuration steps on the left to the correct order on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 24
Refer to the exhibit.

Which two outcomes occur when the state is Other? (Choose two.)

• A. The VSAN on each end of the connection does not match.
• B. The interface is not an E Port.
• C. The interface is not an F Port.
• D. The interface is administratively shut down.
• E. Cisco Fabric Services is not enabled.
• F. NPIV should be disabled.
• G. The interface is functioning, but may have errors.
• H. Encryption is not enable

Answer: CD

NEW QUESTION 25
Refer to the exhibit.

The configuration belongs to which link?

• A. Link A on Switch2
• B. Link B on Switch2
• C. Link C on Switch4
• D. Link D on Switch4

Answer: D

NEW QUESTION 26
Which two items are required components of VN-Link in software? (Choose two.)

• A. VDC
• B. VEM
• C. vPC
• D. VSM
• E. VRRP

Answer: BD

Explanation:
The Cisco Nexus 1000V Series consists of two main types of components that can virtually emulate a 66-slot modular Ethernet switch with redundant supervisor functions:
• Virtual Ethernet module (VEM)-data plane: This lightweight software component runs inside the hypervisor. It enables advanced networking and security features, performs switching between directly attached virtual machines, provides uplink capabilities to the rest of the network, and effectively replaces the vSwitch. Each hypervisor is embedded with one VEM.
• Virtual supervisor module (VSM)-control plane: This standalone, external, physical or virtual appliance is responsible for the configuration, management, monitoring, and diagnostics of the
overall Cisco Nexus 1000V Series system (that is, the combination of the VSM itself and all the VEMs it controls) as well as the integration with VMware vCenter. A single VSM can manage up to 64 VEMs. VSMs can be deployed in an active-standby model, helping ensure high availability.
Reference:
http://www.cisco.com/c/en/us/solutions/collateral/switches/nexus-1000v-switch-vmwarevsphere/ white_paper_c11-525307.html

NEW QUESTION 27
Which statement explains why a Cisco UCS 6200 Fabric Interconnect that is configured in end-host mode is beneficial to the unified fabric network?

• A. There is support for multiple (power of 2) uplinks.
• B. Upstream Layer 2 disjoint networks will remain separated.
• C. The 6200 can connect directly via vPC to a Layer 3 aggregation device.
• D. STP is not required on the uplink ports from the 6200.

Answer: D

Explanation:
http://www.cisco.com/c/en/us/solutions/collateral/data-center-virtualization/unifiedcomputing/whitepaper_c11-701962.html

NEW QUESTION 28
......