Our pass rate is high to 98.9% and the similarity percentage between our cisco ccna 200 125 study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco ccna routing and switching 200 125 pdf exam in just one try? I am currently studying for the Cisco ccna 200 125 syllabus exam. Latest Cisco 200 125 ccna v3 0 Test exam practice questions and answers, Try Cisco cisco ccna 200 125 Brain Dumps First.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/200-125-exam-dumps.html
Q121. - (Topic 3)
Refer to the exhibit.
What can be determined about the router from the console output?
A. No configuration file was found in NVRAM.
B. No configuration file was found in flash.
C. No configuration file was found in the PCMCIA card.
D. Configuration file is normal and will load in 15 seconds.
Answer: A
Explanation:
When no startup configuration file is found in NVRAM, the System Configuration Dialog will appear to ask if we want to enter the initial configuration dialog or not.
Q122. - (Topic 8)
Which routing protocol has the smallest default administrative distance?
A. IBGP
B. OSPF
C. IS-IS
D. EIGRP
E. RIP
Answer: D
Explanation: http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/15986-admin-distance.html
Default Distance Value TableThis table lists the administrative distance default values of the protocols that Cisco supports:
Route Source
Default Distance Values
Connected interface 0
Static route 1
Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5
External Border Gateway Protocol (BGP) 20
Internal EIGRP 90
IGRP 100 OSPF 110
Intermediate System-to-Intermediate System (IS-IS) 115
Routing Information Protocol (RIP) 120
Exterior Gateway Protocol (EGP) 140
On Demand Routing (ODR) 160
External EIGRP 170
Internal BGP 200
Unknown* 255
Q123. - (Topic 5)
What are three approaches that are used when migrating from an IPv4 addressing scheme to an IPv6 scheme. (Choose three.)
A. enable dual-stack routing
B. configure IPv6 directly
C. configure IPv4 tunnels between IPv6 islands
D. use proxying and translation to translate IPv6 packets into IPv4 packets
E. statically map IPv4 addresses to IPv6 addresses
F. use DHCPv6 to map IPv4 addresses to IPv6 addresses
Answer: A,C,D
Explanation:
Several methods are used terms of migration including tunneling, translators, and dual stack. Tunnels are used to carry one protocol inside another, while translators simply translate IPv6 packets into IPv4 packets. Dual stack uses a combination of both native IPv4 and IPv6. With dual stack, devices are able to run IPv4 and IPv6 together and if IPv6 communication is possible that is the preferred protocol. Hosts can simultaneously reach IPv4 and IPv6 content.
Q124. - (Topic 3)
Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D
Explanation:
The “show version” command can be used to show the last method to powercycle (reset) a router.
Q125. - (Topic 7)
Refer to the exhibit.
If the devices produced the given output, what is the cause of the EtherChannel problem?
A. SW1's Fa0/1 interface is administratively shut down.
B. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
C. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
D. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
Answer: D
Explanation:
You must configure all interfaces in an EtherChannel to operate at the same speeds and duplex modes. Based on the output shown, SW1 is configured to run at 10Mb while SW2 is operating at 100 Mb.
Q126. - (Topic 8)
Which statement about named ACLs is true?
A. They support standard and extended ACLs.
B. They are used to filter usernames and passwords for Telnet and SSH.
C. They are used to filter Layer 7 traffic.
D. They support standard ACLs only.
E. They are used to rate limit traffic destined to targeted networks.
Answer: A
Explanation:
Named Access Control Lists (ACLs) allows standard and extended ACLs to be given names instead of numbers. Unlike in numbered Access Control Lists (ACLs), we can edit Named Access Control Lists. Another benefit of using named access configuration mode is that you can add new statements to the access list, and insert them wherever you like. With the legacy syntax, you must delete the entire access list before reapplying it using the updated rules.
Q127. - (Topic 5)
How does a DHCP server dynamically assign IP addresses to hosts?
A. Addresses are permanently assigned so that the host uses the same address at all times.
B. Addresses are assigned for a fixed period of time. At the end of the period, a new request for an address must be made, and another address is then assigned.
C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease.
D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
Answer: C
Explanation:
DHCP works in a client/server mode and operates like any other client/server relationship. When a PC connects to a DHCP server, the server assigns or leases an IP address to that PC. The PC connects to the network with that leased IP address until the lease expires. The host must contact the DHCP server periodically to extend the lease. This lease mechanism ensures that hosts that move or power off do not hold onto addresses that they do not need. The DHCP server returns these addresses to the address pool and reallocates them as necessary.
Q128. - (Topic 5)
The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?
A. 8
B. 6
C. 30
D. 32
E. 14
F. 16
Answer: C
Explanation:
Since there is one class C network that means 256 total IP addresses. Since we need 7 LAN blocks and we cannot use the first one (subnet 0) we take 256/8=32 hosts. However, since we need to reserve the network and broadcast addresses for each of these subnets, only 30 total IP addresses are usable.
Q129. - (Topic 8)
Which statement about switch access ports is true?
A. They drop packets with 802.1Q tags.
B. A VLAN must be assigned to an access port before it is created.
C. They can receive traffic from more than one VLAN with no voice support
D. By default, they carry traffic for VLAN 10.
Answer: A
Explanation:
"If an access port receives a packet with an 802.1Q tag in the header other than the access VLAN value, that port drops the packet without learning its MAC source address."
Q130. - (Topic 7)
Refer to the exhibit.
An administrator pings the default gateway at 10.10.10.1 and sees the output as shown. At which OSI layer is the problem?
A. data link layer
B. application layer
C. access layer
D. session layer
E. network layer
Answer: E
Explanation:
The command ping uses ICMP protocol, which is a network layer protocol used to propagate control message between host and router. The command ping is often used to verify the network connectivity, so it works at the network layer.
