Regenerate 642-980 actual test Guide


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 642-980 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 642-980 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/642-980-exam-dumps.html

Q31. What is the correct configuration for interface Ethernet 1/1 of a Cisco Nexus 5000 Series Switch when it is a member of port channel 101 connected to FEX 101? 

A. interface Ethernet1/1 

switchport mode trunk 

switchport trunk native vlan 10 

switchport trunk allowed vlan 20,30 

fex associate 101 

channel-group 101 

B. interface Ethernet1/1 

switchport mode fex-fabric 

channel-group 101 

C. interface Ethernet1/1 

switchport mode access 

switchport access vlan 10 

fex associate 101 

channel-group 101 

D. interface Ethernet1/1 

switchport mode fex-fabric 

fex associate 101 

channel-group 101 

Answer:


Q32. Refer to the exhibit. 

In the initial SAN deployment or after topology changes in the SAN, some hosts cannot communicate with storage. What are three possible causes of the problem? (Choose three.) 

A. misconfigured fabric timers 

B. misconfigured port parameters 

C. VSAN pruning 

D. VSAN trunking issues 

E. VLAN problems 

F. mismatched zoning 

Answer: ABF 


Q33. FHRP isolation between data center networks that are connected over an OTV network is a two-step process; the first prevents FHRP peering by filtering FHRP control packets across the overlay via a VLAN ACL. What is the second step? 

A. Filter the FHRP MAC addresses that are being advertised by IS-IS. 

B. Remove the FHRP VLAN from the OTV extend-vlan list. 

C. Apply a VLAN to a route map that is applied to the OTV routing process. 

D. Disable the auto-population of the OTV MAC address table. 

Answer:


Q34. A customer is deploying FCoE in its networ and has found that the connected host does not support FIP. Which command will be useful in troubleshooting this issue? 

A. show platform fcoe_mgr info interface vfc id 

B. show platform fcoe_mgr info software interface vfc id 

C. show platform software fcoe_mgr info interface vfc id 

D. show platform software interface fcoe_mgr info vfc id 

Answer:


Q35. Which statement is true regarding Cisco FabricPath? 

A. It is necessary to first install the Cisco FabricPath feature set in the default VDC. 

B. Cisco FabricPath is only available on Cisco Nexus 7010 Switches with the Supervisor 2 engine. 

C. Cisco FabricPath cannot be disabled explicitly for a specific VDC. 

D. If the Cisco FabricPath feature is not installed, the fabricpath keyword will be available in the feature-set command. 

Answer:


Q36. What is one requirement for running FabricPath on a Cisco Nexus 7000 Series switches? 

A. You must have an F Series module 

B. You must run NX-OS version 4.2 to run FabrciPath 

C. ISSU needs to be disabled to run FabricPath 

D. LAN_TRANSPORT_SERVICES_PKG license needs to be installed to run FabrciPath 

Answer:


Q37. Which three of these would cause two switch fabrics not to merge? (Choose three.) 

A. Two or more switches do not have at least one assigned domain ID in common. 

B. Two switches have different assigned VSANs on the connecting ports. 

C. Two switches have different assigned VLANs on the connecting ports. 

D. The static domain ID does not override the dynamic ID. 

E. The election of the static domain is only determined by the WWNs of the two switches. 

F. The physical connectivity between the two switches is not active. 

Answer: ABF 


Q38. Which two statements are true regarding vPC configuration? (Choose two.) 

A. With vPC, there are no blocked ports. 

B. vPC uses hash-based EtherChannel load balancing. 

C. There are STP-blocked redundant links. 

D. There is VLAN-based load balancing. 

E. There is higher oversubscription. 

Answer: AB 


Q39. Refer to the exhibit. 

When suspending or deleting VSANs, which three statements are true? (Choose three.) 

A. You can delete only one VSAN at a time. 

B. You must wait 60 seconds after you enter the vsan suspend command before you enter another command. 

C. You must wait 120 seconds after you enter the vsan suspend command before you enter another command. 

D. You can unsuspend only one VSAN at a time. 

E. You can delete multiple VSANs as long as they are in the same domain. 

F. You can delete multiple VSANs as long as they are in the same zone. 

Answer: ABD 


Q40. Refer to the exhibit. 

When your customers have NPV problems, which three actions should you take? (Choose three.) 

A. Verify that the NPV core switch supports NPIV and that it is enabled. 

B. Verify that all ports are properly configured and connected. 

C. Ensure that the VLAN values are configured on both sides of the NPV core switch. 

D. Verify the status of the servers and external interfaces, using the show npv server status command. 

E. Ensure that the VSAN value that is configured on the device links is correct. 

F. For all the device links, ensure that the port mode on the NPV device is in Full_port mode. 

Answer: ABE