Top Tips Of JN0-692 cram

Juniper JN0-692 replies, JN0-692 official certifications queries, The past few years, Juniper grows more and a lot more well-known. Along with Juniper JN0-692 exam is extremely accommodate those who are interesting during the it sector. If an individual wants to complete the actual Juniper JN0-692 exam, and obtain the actual Juniper official certifications productively, only need to decide on Juniper JN0-692 examine Q&As for preparation components properly.

2021 Feb JN0-692 exam

Q81. Click the Exhibit button. 

As shown in the exhibit, you have an LSP established from R1 to R4. Your network experiences a link failure between R2 and R3.Which statement is correct? 

A. A ResvTear message is sent toward the egress router. 

B. A ResvConf message is sent toward the ingress router. 

C. A PathErr message is sent toward the egress router. 

D. A ResvTear message is sent toward the ingress router. 

Answer:


Q82. The network design team has decided to activate multicast in the network. Auto-RP has been selected as the RP mechanism. Which PIM operational mode must be enabled in this network? 

A. sparse mode 

B. sparse-dense mode 

C. dense mode 

D. source specific multicast 

Answer:


Q83. Click the Exhibit button. 

In the exhibit, R1 and R2 have a static default route configured that points toward the provider. Both routers redistribute the default route into OSPF. R2 is the preferred gateway to reach the provider. R1 is the backup gateway. All link metrics are equal. Which two steps ensure that traffic to the provider flows through R2 while the network is working properly? (Choose two.) 

A. Redistribute the default route as a Type 1 external route on router R1 and a Type 2 external route on router R2. 

B. Redistribute the default route as a Type 2 external route on router R1 and a Type 1 external route on router R2. 

C. Modify the preference value of the default route on router R1 so that it is less preferred than OSPF external routes. 

D. Modify the preference value of the default route on router R2 so that it is more preferred than OSPF external routes. 

Answer: B, C 


Q84. Referring to the exhibit, which statement is true assuming LDP VPN signaling? 

A. PE1 uses the label value received from PE2 for VPN B as the inner label for VPN 

B. 

B. PE2 uses the label value received from PE1 for VPN A as the transport label for VPN A. 

C. P1 uses the label value for VPN A advertised by PE1, because RSVP is enabled. 

D. PE1 uses the transport label value received for VPN A that is advertised by PE2 as the inner label for VPN A. 

Answer:


Q85. Which two configuration parameters are required to configure an LDP-signaled VPLS service? (Choose two.) 

A. vpls-id 

B. site-identifier 

C. route-distinguisher 

D. instance-type vpls 

Answer: A, D 


Renewal JN0-692 exam topics:

Q86. Which three statements are true about the BGP community attribute? (Choose three.) 

A. There are three well-known communities. 

B. Communities can be used to signal local preference in other AS networks. 

C. Only well-known communities can be passed between AS networks. 

D. Routing policies can be simplified using BGP communities. 

E. Communities are used in the route selection process. 

Answer: A, B, D 


Q87. In your network, customers are complaining about the performance of voice traffic. 

Which command displays the number of packets dropped due to the drop profile configured? 

A. show interfaces queue ge-1/0/0 

B. show interfaces terse 

C. show class-of-service interface ge-1/0/0 

D. show class-of-service forwarding-class 

Answer:


Q88. Click the Exhibit button. 

Your employer is ISP A. Your customers must be able to reach customers of both ISP B and ISP C, but your network must not allow transit traffic between ISP B and ISP C at any time. Referring to the exhibit, what are two solutions? (Choose two.) 

A. Use policy to filter routes on AS number. B. Use the well-known no-export community. C. Use the MED to prefer the proper routes. 

D. Use communities to identify and filter routes. 

Answer: A, D 


Q89. Click the Exhibit button. 

R1 and R2 are directly connected using the interfaces shown in the exhibit. R1 can ping R2's interface, and R2 can ping R1's interface. The IS-IS adjacency will not come up. What is causing the adjacency to fail? 

A. The correct levels are not configured under protocols isis. 

B. The link MTU is too small to support IS-IS. 

C. Authentication is not properly configured for the adjacency. 

D. Both routers are configured as the DR, causing a conflict. 

Answer:


Q90. Which choice shows the configuration in the exhibit in SLAX format? A. Option A 

B. Option B 

C. Option C 

D. Option D 

Answer:



see more JN0-692 dumps