Replace Cisco 200-125 - An Overview 11 to 20

The That field is demanding new experimentations and innovations all the time. This particular calls for constant improvement of data with fresh concepts. So you can find always a few changes in the actual real Cisco 200-125 exam. Each of our professionals are dedicated to revising the Cisco Cisco exam dumps timely. We ensure that we give you the newest and most official and reliable Cisco 200-125 preparation supplies. We promise your wonderful success in the Cisco Cisco actual exam by making use of our professionally gathered preparation materials.

2016 Oct 200-125 exam prep

Q11. - (Topic 4) 

Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices? 

A. enable cdp 

B. cdp enable 

C. cdp run 

D. run cdp 

Answer: C 


Q12. - (Topic 7) 

Scenario 

Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links. 

You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices. 









An OSPF neighbor adjacency is not formed between R3 in the main office and R6 in the Branch3 office. What is causing the problem? 

A. There is an area ID mismatch. 

B. There is a PPP authentication issue; the username is not configured on R3 and R6. 

C. There is an OSPF hello and dead interval mismatch. 

D. The R3 router ID is configured on R6. 

Answer: D 


Q13. - (Topic 5) 

Which three statements about the features of SNMPv2 and SNMPv3 are true? (Choose three.) 

A. SNMPv3 enhanced SNMPv2 security features. 

B. SNMPv3 added the Inform protocol message to SNMP. 

C. SNMPv2 added the Inform protocol message to SNMP. 

D. SNMPv3 added the GetBulk protocol messages to SNMP. 

E. SNMPv2 added the GetBulk protocol message to SNMP. 

F. SNMPv2 added the GetNext protocol message to SNMP. 

Answer: A,C,E 


Q14. - (Topic 3) 

Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.) 

A. Global addresses start with 2000::/3. 

B. Link-local addresses start with FE00:/12. 

C. Link-local addresses start with FF00::/10. 

D. There is only one loopback address and it is ::1. 

E. If a global address is assigned to an interface, then that is the only allowable address for the interface. 

Answer: A,D 


Q15. DRAG DROP - (Topic 4) 


Answer: 



200-125 question

Updated 200-125 actual exam:

Q16. - (Topic 4) 

Which command shows your active Telnet connections? 

A. show cdp neigbors 

B. show session 

C. show users 

D. show vty logins 

Answer: B 


Q17. - (Topic 2) 

Which switch would STP choose to become the root bridge in the selection process? 

A. 32768: 11-22-33-44-55-66 

B. 32768: 22-33-44-55-66-77 

C. 32769: 11-22-33-44-55-65 

D. 32769: 22-33-44-55-66-78 

Answer: A 


Q18. - (Topic 9) 

Which standards-based First Hop Redundancy Protocol is a Cisco supported alternative to Hot Standby Router Protocol? 

A. VRRP 

B. GLBP 

C. TFTP 

D. DHCP 

Answer: A 


Q19. - (Topic 4) 

Refer to the exhibit. 


Why is flash memory erased prior to upgrading the IOS image from the TFTP server? 

A. The router cannot verify that the Cisco IOS image currently in flash is valid. 

B. Flash memory on Cisco routers can contain only a single IOS image. 

C. Erasing current flash content is requested during the copy dialog. 

D. In order for the router to use the new image as the default, it must be the only IOS image in flash. 

Answer: C 


Q20. - (Topic 9) 

Which type of address is the public IP address of a NAT device? 

A. outside global 

B. outside local 

C. inside global 

D. inside local 

E. outside public 

F. inside public 

Answer: C 



see more 200-125 dumps