♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 210-065 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 210-065 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/210-065-exam-dumps.html
Q21. A Cisco TelePresence EX Series desktop endpoint failed to register to a Cisco VCS. The SIP status shows "Failed: 403 Forbidden" in the endpoint's web interface. What is the first thing that should be checked in the endpoint configuration settings?
A. Verify that the correct SIP authentication credentials have been configured.
B. Ensure that CallSetup Mode is set to Gatekeeper.
C. Verify that Outbound Connection Credentials are properly configured.
D. Check to see that SIP Mode is set to On.
Answer: A
Q22. What is the importance of defining option 150 in the DHCP server for Cisco TelePresence endpoints?
A. Option 150 is not important.
B. It is the TFTP server IPv4 address where the video endpoint retrieves its configuration file while booting.
C. It is the IPv4 address of the default gateway for the subnet that the video endpoint is connected to.
D. It is the configured SIP registrar and proxy server.
E. It is the unique NTP server IPv4 address.
Answer: B
Q23. Refer to the exhibit.
The customer recently connected a new TV monitor to the Cisco TelePresence endpoint. This device is now showing a warning concerning the echo cancellation delay. Which action could help mitigate this issue?
A. Turn off any postprocessing settings.
B. Turn off 3D mode on the new TV.
C. Turn on Frequency Scan Acceleration for the new TV.
D. Turn off surround sound on the new TV.
Answer: A
Q24. An engineer is configuring a Cisco TelePresence System endpoint for use with a maximum of six people in the room. Which table type should be configured when setting up cameras where two participants directly face the endpoint display?
A. short racetrack
B. long racetrack
C. short rectangle
D. long rectangle
Answer: A
Q25. Which function does a Cisco TCS recording alias perform?
A. It links recorded media to a specified output location.
B. It provides a dialable alias that will trigger a TCS recording workflow.
C. It sends media to Cisco Medianet.
D. It provides an alias for the recorded filename.
Answer: B
Q26. Which of these needs to be enabled in Cisco Unified Communications Manager in order for the Cisco TelePresence System 500-32 to be able to share a presentation with a Cisco TelePresence System Codec C40 endpoint that is registered to a VCS?
A. Allow iX application media
B. Send send-receive SDP in mid-call invite
C. Allow presentation sharing using BFCP
D. Allow presentation sharing using H.235
E. Deliver conference bridge identifier
Answer: C
Q27. The firmware for the primary codec of a Cisco TelePresence System 3010 is being upgraded. Which codec CLI command could be used to check on the progress of the update?
A. utils upgrade display
B. utils system version
C. show upgrade detail
D. show system upgrade
Answer: C
Q28. Which two of these are required in order to complete the password recovery of a Cisco TelePresence System endpoint? (Choose two.)
A. must have FTP enabled on the endpoint
B. must have SSH enabled on the endpoint
C. must have the security question answer for the endpoint
D. must be in the same room as the main display
E. must have SFTP enabled on the endpoint
F. must call Cisco TAC for the security code
Answer: B,D
Q29. Which statement is true about the Cisco TelePresence System 500-32 system regarding the HVAC needs for the room where it is installed?
A. The system does not require any additional requirements above the normal HVAC requirements for the room.
B. You must supply additional cooling requirements for the room.
C. You must supply a room that has energy-efficient lighting to reduce the temperature of the room.
D. The temperature of the room will be 10 to 20 degrees warmer than the rest of the building.
Answer: A
Q30. A Cisco TelePresence VCS displays this alarm: "Root password is set to default." How can this security warning be addressed?
A. Use the Cisco TelePresence VCS web user interface, choose Administration > User Settings, and change the root password.
B. Use SSH to log in to the Cisco TelePresence VCS as Administrator and issue the command xconfig root set passwd.
C. Use SSH to log in to the Cisco TelePresence VCS as Root, issue the command set password, and enter the new password when prompted.
D. Use SSH to log in to the Cisco TelePresence VCS as Root, issue the command passwd, and enter the new password when prompted.
E. Use the Cisco TelePresence VCS web user interface, choose Administration > System Settings, and change the root password.
Answer: D
